alpha ra7000 disk failed , power failed ,help !!!

[mac2008_1]

alpha ra7000 disk failed , power failed ,help !!!what can replace disk and POWER ?

MESSAGE:

Starting HSZterm Version V1.1A
Copyright Digital Equipment Corporation 1996. All rights reserved


Copyright Compaq Computer Corporation 1993, 1998. All rights reserved.
HSZ70 Firmware version V73Z-0, Hardware version H04

Last fail code: 018000A0

Press " ?" at any time for help.


Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show storagesets full

Name Storageset Uses Used by
------------------------------------------------------------------------------

R1 raidset DISK10000 D0
DISK20000
DISK30000
DISK40000
DISK60100
Switches:
POLICY (for replacement) = BEST_PERFORMANCE
RECONSTRUCT (priority) = NORMAL
CHUNKSIZE = 256 blocks
State:
NORMAL
DISK10000 (member 0) is NORMAL
DISK20000 (member 1) is NORMAL
DISK30000 (member 2) is NORMAL
DISK40000 (member 3) is NORMAL
DISK60100 (member 4) is NORMAL
Size: 142190816 blocks

R2 raidset DISK10100 D100
DISK20100
DISK30100
DISK40100
Switches:
POLICY (for replacement) = BEST_PERFORMANCE
RECONSTRUCT (priority) = NORMAL
CHUNKSIZE = 256 blocks
State:
REDUCED
DISK10100 (member 0) is NORMAL
DISK20100 (member 1) is NORMAL
DISK30100 (member 2) is NORMAL
DISK40100 (member 3) is NORMAL
Size: 142190816 blocks

SPARESET spareset

FAILEDSET failedset DISK50000
DISK50100
DISK60000
Switches:
NOAUTOSPARE
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show raidset full

Name Storageset Uses Used by
------------------------------------------------------------------------------

R1 raidset DISK10000 D0
DISK20000
DISK30000
DISK40000
DISK60100
Switches:
POLICY (for replacement) = BEST_PERFORMANCE
RECONSTRUCT (priority) = NORMAL
CHUNKSIZE = 256 blocks
State:
NORMAL
DISK10000 (member 0) is NORMAL
DISK20000 (member 1) is NORMAL
DISK30000 (member 2) is NORMAL
DISK40000 (member 3) is NORMAL
DISK60100 (member 4) is NORMAL
Size: 142190816 blocks

R2 raidset DISK10100 D100
DISK20100
DISK30100
DISK40100
Switches:
POLICY (for replacement) = BEST_PERFORMANCE
RECONSTRUCT (priority) = NORMAL
CHUNKSIZE = 256 blocks
State:
REDUCED
DISK10100 (member 0) is NORMAL
DISK20100 (member 1) is NORMAL
DISK30100 (member 2) is NORMAL
DISK40100 (member 3) is NORMAL
Size: 142190816 blocks
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show units full

LUN Uses
--------------------------------------------------------------

D0 R1
Switches:
RUN NOWRITE_PROTECT READ_CACHE
WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
ACCESS_ID = ALL
State:
ONLINE to this controller
Reserved
PREFERRED_PATH = THIS_CONTROLLER
Size: 142190816 blocks
D100 R2
Switches:
RUN NOWRITE_PROTECT READ_CACHE
WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
ACCESS_ID = ALL
State:
ONLINE to this controller
Reserved
PREFERRED_PATH = THIS_CONTROLLER
Size: 142190816 blocks
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show devices full

Name Type Port Targ Lun Used by
------------------------------------------------------------------------------

DISK10000 disk 1 0 0 R1
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK10100 disk 1 1 0 R2
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK20000 disk 2 0 0 R1
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK20100 disk 2 1 0 R2
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK30000 disk 3 0 0 R1
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK30100 disk 3 1 0 R2
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK40000 disk 4 0 0 R1
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK40100 disk 4 1 0 R2
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK50000 disk 5 0 0 FAILEDSET
Misconfigured: No device at this PTL, please see user guide
DISK50100 disk 5 1 0 FAILEDSET
Misconfigured: No device at this PTL, please see user guide
DISK60000 disk 6 0 0 FAILEDSET
Misconfigured: No device at this PTL, please see user guide
DISK60100 disk 6 1 0 R1
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show failedset

Name Storageset Uses Used by
------------------------------------------------------------------------------

FAILEDSET failedset DISK50000
DISK50100
DISK60000
Switches:
NOAUTOSPARE
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show this full

Controller:
HSZ70 ZG93207867 Firmware V73Z-0, Hardware H04
Configured for dual-redundancy with ZG93207803
In dual-redundant configuration
Device Port SCSI address 7
Time: NOT SET
Host port:
SCSI target(s) (0, 1, 2, 3)
Preferred target(s) (0, 1)
TRANSFER_RATE_REQUESTED = 20MHZ
Host Functionality Mode = A
Allocation class 0
Command Console LUN is target 0, lun 1
Cache:
32 megabyte write cache, version 4
Cache is GOOD
Battery is GOOD
Unflushed data in cache
CACHE_FLUSH_TIMER = DEFAULT (10 seconds)
NOCACHE_UPS
Mirrored Cache:
32 megabyte write cache, version 4
Cache is GOOD
Battery is GOOD
Unflushed data in cache
Extended information:
Terminal speed 9600 baud, eight bit, no parity, 1 stop bit
Operation control: 00000004 Security state code: 90916
Configuration backup disabled
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show other full

Controller:
HSZ70 ZG93207803 Firmware V73Z-0, Hardware H04
Configured for dual-redundancy with ZG93207867
In dual-redundant configuration
Device Port SCSI address 6
Time: NOT SET
Host port:
SCSI target(s) (0, 1, 2, 3)
Preferred target(s) (2, 3)
TRANSFER_RATE_REQUESTED = 20MHZ
Host Functionality Mode = A
Allocation class 0
Command Console LUN is target 0, lun 1
Cache:
32 megabyte write cache, version 4
Cache is GOOD
Battery is GOOD
No unflushed data in cache
CACHE_FLUSH_TIMER = DEFAULT (10 seconds)
NOCACHE_UPS
Mirrored Cache:
32 megabyte write cache, version 4
Cache is GOOD
Battery is GOOD
No unflushed data in cache
Extended information:
Terminal speed 9600 baud, eight bit, no parity, 1 stop bit
Operation control: 00000004 Security state code: 69130
Configuration backup disabled
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show connection

Error 9060: Container or unit CONNECTION does not exist
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show failedset

Name Storageset Uses Used by
------------------------------------------------------------------------------

FAILEDSET failedset DISK50000
DISK50100
DISK60000
Switches:
NOAUTOSPARE
Power Supply failure cleared.
Temperature is within optimum range.

[Patrick Pletscher]

Hi mac2008

It looks like the following disks are dead
DISK50000
DISK50100
DISK60000

You can see that with the the command show device full:

Your output is:
DISK50000 disk 5 0 0 FAILEDSET
Misconfigured: No device at this PTL, please see user guide
DISK50100 disk 5 1 0 FAILEDSET
Misconfigured: No device at this PTL, please see user guide
DISK60000 disk 6 0 0 FAILEDSET
Misconfigured: No device at this PTL, please see user guide

And your Unit D100 is in a reduced state.

R2 raidset D100
DISK10100
DISK20100
DISK30100
DISK40100
Switches:
POLICY (for replacement) = BEST_PERFORMANCE
RECONSTRUCT (priority) = NORMAL
CHUNKSIZE = 256 blocks
State:
REDUCED
DISK10100 (member 0) is NORMAL
DISK20100 (member 1) is NORMAL
DISK30100 (member 2) is NORMAL
DISK40100 (member 3) is NORMAL
Size: 142190816 blocks


I would replace these 3 disks.

Do the following for all three disks:

del failedset disk50000
del disk50000
replace the disk
add disk DISK50000 5 0 0
init disk50000
add spareset disk50000

Than the raidset will automatically start the rebuild proces.

regards

Patrick

[mac2008_1]

thank you for Patrick Pletscher , I have do it ,now ra7000 status become normal!