- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- configure a new disk in disk array 12H
Disk Enclosures
1752648
Members
5732
Online
108788
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-27-2004 05:53 AM
05-27-2004 05:53 AM
configure a new disk in disk array 12H
hi,
I plugged a new disk in the the disk array 12H
with the control pannel I performed the balancing.
After the balancing I want to extend my volume group vgora with the new disk.
May I have to create a new lun and perform
pvcreate as follows :
1)arraycfg -L 2 -a 512 serial_id
2) pvcreate
3) vgextend.
the pvcreate is it mandatory ?
please help us.
kuzo
I plugged a new disk in the the disk array 12H
with the control pannel I performed the balancing.
After the balancing I want to extend my volume group vgora with the new disk.
May I have to create a new lun and perform
pvcreate as follows :
1)arraycfg -L 2 -a 512 serial_id
2) pvcreate
3) vgextend.
the pvcreate is it mandatory ?
please help us.
kuzo
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-27-2004 05:12 PM
05-27-2004 05:12 PM
Re: configure a new disk in disk array 12H
If the disk is new then you will have to perform pvcreate on the disk before putting it into a volume group.
I assume that you are worried that you may lose data if you specify the wrong disk?
Run pvcreate, but don't use the -f option and you should be fine. It will prompt if it is already in use.
Hope this helps.
I assume that you are worried that you may lose data if you specify the wrong disk?
Run pvcreate, but don't use the -f option and you should be fine. It will prompt if it is already in use.
Hope this helps.
"I'm the Man"
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP