1748011 Members
3736 Online
108757 Solutions
New Discussion юеВ

Re: hp va 7100

 
saj_2
Advisor

hp va 7100

I have a HP va 7100 machine .

When i wanted to use it , it didnt function properly so i connected it to a console through a serial cable .

and in the command prompt it read "no map " ..

what do i do next ?? what does it mean??
15 REPLIES 15
Luk Vandenbussche
Honored Contributor

Re: hp va 7100

Hi,
no map means that the array is not configured.

Follow the flow chart in the link below

http://h20000.www2.hp.com/bc/docs/support/SupportManual/lpg28975/lpg28975.pdf

saj_2
Advisor

Re: hp va 7100

thanks a lot for thte fast reply ..:-)

but I'm not using a SDM. and I will have to download one . (wonder if I can) ..

nyways ... I was using the hyper terminal and found out that when I give command dsp -c command it shows one cotroller to be in a failed state ..
what does a failed controller mean ?? I dont have a spare one to replace this ..

seeking you advice
saj_2
Advisor

Re: hp va 7100

just rebooter the system and formatted the disks and the prompt changed to cli>

thanks for the help.
Luk Vandenbussche
Honored Contributor

Re: hp va 7100

hi,

you can dowload the softwares here

http://h20000.www2.hp.com/bizsupport/TechSupport/DriverDownload.jsp?тМй=en&cc=us&prodNameId=30591&taskId=135&prodTypeId=12169&prodSeriesId=64112тМй=en&cc=us

A failed controller means a defective controller. If you have a hw contract then HP must replace this controller
Arend Lensen
Trusted Contributor

Re: hp va 7100

A failed controller could be caused by a faulty or completely depleted battery.
Can you post the output of the dsp -c -s command?
saj_2
Advisor

Re: hp va 7100

Warning State > dsp -s -c

SUBSYSTEM SETTINGS:
Capacity Depletion Threshold: 0
Subsystem Level RAID Control: AutoRAID
Enable Manual Override: FALSE
Manual Override Destination: FALSE
Enable Optimize Policy: TRUE
Read Cache Disable: FALSE
Write Cache Enable: FALSE
Enable Prefetch: FALSE
Rebuild Priority: LOW
Security Enabled: FALSE
Shutdown Completion: 0
Subsystem Type ID: 0
Unit Attention: TRUE
Disabl Sec Path Presentation: FALSE
Volume Set Partitioning: FALSE
Write Working Set Interval: 8640
JBOD Port Data Speed: 1
Queue Full Threshold: 240

RESILIENCY SETTINGS
Enable Secure Mode: TRUE
Disable NVRAM on UPS Absent: FALSE
Disable NVRAM on WCE False: FALSE
Disable Read Hits: FALSE
Force Unit Access Response: 1
Lock Write Cache On: TRUE
Resiliency Threshold: 4 s
Single Controller Warning: TRUE

DISK SETTINGS
Auto Include: TRUE
Auto Rebuild: TRUE
Hot Spare Mode: Automatic
Max Drives per Subsystem: 15

LUN SETTINGS
LUN Creation Limit: 128
Maximum LUN Creation Limit: 128
Migrating Write Destination: FALSE

HOST PORT SETTINGS
Controller 1
Host OS: Windows NT
Port Data Rate: 1 GB/sec
Topology: Public Loop
Loop ID: 111

Controller 2
Host OS: Windows NT
Port Data Rate: 1 GB/sec
Topology: Public Loop
Loop ID: 112

STATUS
Subsystem State: 1


WARNINGS
RAM Unmirrored
Code Mismatch
Single Controller
GBIC Problem

CONTROLLER AT M/C1
Controller State: Unknown
Serial Number:
Vendor ID:
Product ID:
Product Revision:
Host OS: Windows NT
Battery Charger FW Revision: 255.253

HOST PORT INFORMATION
Status: Good
Port WWN: 0x0000000000000000
Link State: Offline
-----------------------------------------------------------

CONTROLLER AT M/C2
Controller State: Good
Serial Number: 00PR03010424
Vendor ID: HP
Product ID: A6188A
Product Revision: HP18
Host OS: Windows NT
Battery Charger FW Revision: 4.1

HOST PORT INFORMATION
Status: Good
Port WWN: 0x50060b00000993c6
Link State: Down
-----------------------------------------------------------
Warning State >
Arend Lensen
Trusted Contributor

Re: hp va 7100

This is interesting:

"Code Mismatch".

Is there data on the array?
If not can you pull the handle for one controller (don't pull the controller out, just release the handle) and see if the other boots up ok.
Then shut it down and see if the other controller boots. For both output capture the dsp -c -f -d -e -L -s (one command)

Arend
saj_2
Advisor

Re: hp va 7100

when i removed the first controller and booted with only the second controller present.....


Warning State > dsp -c -f -d -e -L -s

Controller 1 Not Present

CONTROLLER AT M/C2
Controller State: Good
Serial Number: 00PR03010424
Vendor ID: HP
Product ID: A6188A
Product Revision: HP18
Host OS: Windows NT
Battery Charger FW Revision: 4.1

HOST PORT INFORMATION
Status: Good
Port WWN: 0x50060b00000993c6
Link State: Down
-----------------------------------------------------------

FRU LOCATION HARDWARE COMPONENT IDENTIFICATION STATUS
=========================================================================

M Main Enclosure 00SG139G0083 Warning State
M/C2 AutoRaid Controller 2 00PR03010424 Good
M/C2.B1 NVRAM Battery 000000014987 Good
M/C2.M1 Memory DIMM Not Applicable Good
M/C2.H1 Host Port 000000000070 Good
M/D1 Disk 1 3EV08CW8 Included
M/D2 Disk 2 3EV0CP2A Included
M/D3 Disk 3 3EV0789K Included
M/D4 Disk 4 3EV0CPFC Included
M/D5 Disk 5 3CD2DXL5 Included
M/D6 Disk 6 3CD2DYN6 Included
M/D11 Disk 11 3CD2E0ET Included
M/D12 Disk 12 3CD2BMFE Included
M/D13 Disk 13 3CD2E0QZ Included
M/D14 Disk 14 3CD2E0P0 Included
M/D15 Disk 15 3CD2E18J Included
M/T2.GH2 Host GBIC A28KM1L Critical

DISK AT M/D1:
Drive State: Included
Vendor ID: HP 18.2G
Product ID: ST318452FC
Product Revision: HP03
Capacity: 16896 MB
Loop Address: 111
Node WWN: 0x20000004cf43cbb7
Initialization State: Ready
Volume Set Serial No: 000028B800000011
Block Size: 520
Serial Number: 3EV08CW8
Recovery Maps are on this disk.

DISK AT M/D2:
Drive State: Included
Vendor ID: HP 18.2G
Product ID: ST318452FC
Product Revision: HP03
Capacity: 16896 MB
Loop Address: 112
Node WWN: 0x20000004cf5d4956
Initialization State: Ready
Volume Set Serial No: 000028B800000011
Block Size: 520
Serial Number: 3EV0CP2A
Recovery Maps are on this disk.

DISK AT M/D3:
Drive State: Included
Vendor ID: HP 18.2G
Product ID: ST318452FC
Product Revision: HP03
Capacity: 16896 MB
Loop Address: 113
Node WWN: 0x20000004cf43cd36
Initialization State: Ready
Volume Set Serial No: 000028B800000011
Block Size: 520
Serial Number: 3EV0789K

DISK AT M/D4:
Drive State: Included
Vendor ID: HP 18.2G
Product ID: ST318452FC
Product Revision: HP03
Capacity: 16896 MB
Loop Address: 114
Node WWN: 0x20000004cf5d4897
Initialization State: Ready
Volume Set Serial No: 000028B800000011
Block Size: 520
Serial Number: 3EV0CPFC

DISK AT M/D5:
Drive State: Included
Vendor ID: HP 36.4G
Product ID: ST336704FC
Product Revision: HPC3
Capacity: 33792 MB
Loop Address: 115
Node WWN: 0x20000004cf237559
Initialization State: Ready
Volume Set Serial No: 000028B800000011
Block Size: 520
Serial Number: 3CD2DXL5

DISK AT M/D6:
Drive State: Included
Vendor ID: HP 36.4G
Product ID: ST336704FC
Product Revision: HPC3
Capacity: 33792 MB
Loop Address: 116
Node WWN: 0x20000004cf237466
Initialization State: Ready
Volume Set Serial No: 000028B800000011
Block Size: 520
Serial Number: 3CD2DYN6

DISK AT M/D11:
Drive State: Included
Vendor ID: HP 36.4G
Product ID: ST336704FC
Product Revision: HPC3
Capacity: 33792 MB
Loop Address: 121
Node WWN: 0x20000004cf2375a3
Initialization State: Ready
Volume Set Serial No: 000028B800000011
Block Size: 520
Serial Number: 3CD2E0ET

DISK AT M/D12:
Drive State: Included
Vendor ID: HP 36.4G
Product ID: ST336704FC
Product Revision: HPC3
Capacity: 33792 MB
Loop Address: 122
Node WWN: 0x20000004cf237417
Initialization State: Ready
Volume Set Serial No: 000028B800000011
Block Size: 520
Serial Number: 3CD2BMFE

DISK AT M/D13:
Drive State: Included
Vendor ID: HP 36.4G
Product ID: ST336704FC
Product Revision: HPC3
Capacity: 33792 MB
Loop Address: 123
Node WWN: 0x20000004cf237582
Initialization State: Ready
Volume Set Serial No: 000028B800000011
Block Size: 520
Serial Number: 3CD2E0QZ

DISK AT M/D14:
Drive State: Included
Vendor ID: HP 36.4G
Product ID: ST336704FC
Product Revision: HPC3
Capacity: 33792 MB
Loop Address: 124
Node WWN: 0x20000004cf237739
Initialization State: Ready
Volume Set Serial No: 000028B800000011
Block Size: 520
Serial Number: 3CD2E0P0

DISK AT M/D15:
Drive State: Included
Vendor ID: HP 36.4G
Product ID: ST336704FC
Product Revision: HPC3
Capacity: 33792 MB
Loop Address: 109
Node WWN: 0x20000004cf2376b8
Initialization State: Ready
Volume Set Serial No: 000028B800000011
Block Size: 520
Serial Number: 3CD2E18J

Total capacity of physical disks in array = 297 GB


Enclosure at M:
Loop Pair: 255
Enclosure ID: 0
Enclosure Status: FC Port Problem
Enclosure Type: MAIN
Serial Number: 0x00SG139G0083


There are no LUNS Configured.


SUBSYSTEM SETTINGS:
Capacity Depletion Threshold: 0
Subsystem Level RAID Control: AutoRAID
Enable Manual Override: FALSE
Manual Override Destination: FALSE
Enable Optimize Policy: TRUE
Read Cache Disable: FALSE
Write Cache Enable: FALSE
Enable Prefetch: FALSE
Rebuild Priority: LOW
Security Enabled: FALSE
Shutdown Completion: 0
Subsystem Type ID: 0
Unit Attention: TRUE
Disabl Sec Path Presentation: FALSE
Volume Set Partitioning: FALSE
Write Working Set Interval: 8640
JBOD Port Data Speed: 1
Queue Full Threshold: 240

RESILIENCY SETTINGS
Enable Secure Mode: TRUE
Disable NVRAM on UPS Absent: FALSE
Disable NVRAM on WCE False: FALSE
Disable Read Hits: FALSE
Force Unit Access Response: 1
Lock Write Cache On: TRUE
Resiliency Threshold: 4 s
Single Controller Warning: TRUE

DISK SETTINGS
Auto Include: TRUE
Auto Rebuild: TRUE
Hot Spare Mode: Automatic
Max Drives per Subsystem: 15

LUN SETTINGS
LUN Creation Limit: 128
Maximum LUN Creation Limit: 128
Migrating Write Destination: FALSE

HOST PORT SETTINGS
Controller 2
Host OS: Windows NT
Port Data Rate: 1 GB/sec
Topology: Public Loop
Loop ID: 112

STATUS
Subsystem State: 1


WARNINGS
Single Controller
GBIC Problem
Warning State >

Arend Lensen
Trusted Contributor

Re: hp va 7100

This looks fine.
Now the other...