- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- possibility to configure RAID after installing sys...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-04-2008 02:10 AM
тАО07-04-2008 02:10 AM
possibility to configure RAID after installing system
after an initial installation of a server HP, I forgot to configure the RAID (other manufacturers implements basic). Is it possible to configure while the OS and applications are already installed?
if so, how? thank you
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-04-2008 02:12 AM
тАО07-04-2008 02:12 AM
Re: possibility to configure RAID after installing system
HP Proliant ML310 G5
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-04-2008 02:14 AM
тАО07-04-2008 02:14 AM
Re: possibility to configure RAID after installing system
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-04-2008 02:20 AM
тАО07-04-2008 02:20 AM
Re: possibility to configure RAID after installing system
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-04-2008 02:34 AM
тАО07-04-2008 02:34 AM
Re: possibility to configure RAID after installing system
In ML110 G4 there was the possibility of manually loading the driver in Windows before enabling hardware RAID:
Go to Control Panel-> Add New Hardware->Device is connected->New Hardware->Raid Controller->Have Disk->Browse to the folder where the Embedded SATA RAID Drivers were extracted. Select the .inf file->Install Adaptec Raid Driver .
Restart the Server go to BIOS enable the Embedded SATA RAID .
Press F8 and go to Sata Raid BIOS->Configure the Drives->Create Array->Raid 0/1 A warning message will appear "Warning: Configuring the drives will erase all Array information from the selected drives, if that drive is part of an array. Arrays using any of these drives as members will be affected! Do you want to continue?(Yes/No): ". Press "Y " to continue.
If Raid 1 is selected it will ask you what is the Source Disk, select the Right Disk in which OS was installed previously. Warning message might appear again. Select "Y ".
Rebuild will take sometime, once rebuild is complete restart the server.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-04-2008 03:37 AM
тАО07-04-2008 03:37 AM