virtual array 7110 installation

[jpcast_real]

Hello ,

I am trying to install a new virtual array 7110 . I follow all the installation steps from the manual and when I try to format the virtual array "vfpfmt" the system cancels the format . When I also try to create the "LUN 0" , the system says that the space is not correct , I have tried:

cfg -L 0 -a 1M -g 1
and
cfg -L 0 -a 1K -g 1

Anyone knows what can be happening???

Regards

[Joshua Scott]

What interface are you using to set up the system?

The VA7110 comes with a very easy to use GUI and MUI. if you've installed commandView, then just type cvui at the hp-ux prompt and you can go through the menus to configure the LUNs.

Also, the CommandView CD-ROM has a complete manual on the setup and configuration of CommandView.

Josh

[jpcast_real]

I am still just administering it using a direct serial cable . I must create LUN 0 and format the device but can't . This is what I get :

No Map > vfpcfg -L 0 -a 1M -g 1

Unable to Create LUN. Invalid capacity.

No Map > vfpcfg -L0 -a 10M -g 1

Invalid option: -L0

No Map > vfpcfg -L 0 -a 10M -g 1

Unable to Create LUN. Invalid capacity.


No Map > vfpcfg -L 0 -a 20M -g 1

Unable to Create LUN. Invalid capacity.


No Map > vfpfmt
Format Array. Clear ALL data? (yes/no):y


Format Canceled.



No Map > dsp

ARRAY INFORMATION
Array World Wide Name: 0x50060b000014f85a
Alias:
Array State: No Map
---------------------------------------------------

CONTROLLER ENCLOSURE INFORMATION
Serial Number: 00DEH43519SY
Status Summary: OK


No Map >



No Map > dsp -M/C1



Controller State: Good
Serial Number: 00PR00D52487
Vendor ID: HP
Product ID: A6189B
Product Revision: A120
Battery Charger FW Revision: 5.0

HOST PORT1 INFORMATION
Status: Good
Host OS: HPUX
Port WWN: 0x50060b000023385c
Link State: Up
Port Data Rate: 2 GB/sec
Queue Full Threshold: 750
Topology: Direct Fabric Attach
NPort ID: 0x040400

JBOD PORT1 INFORMATION
Status: Good
Link State: Up
Port Data Rate: 2 GB/sec
-----------------------------------------------------------

No Map >


No Map > dsp -c M/C2

AT M/C2
Controller State: Good
Serial Number: 00PR00D50505
Vendor ID: HP
Product ID: A6189B
Product Revision: A120
Battery Charger FW Revision: 5.0

HOST PORT1 INFORMATION
Status: Good
Host OS: HPUX
Port WWN: 0x50060b00002338ce
Link State: Up
Port Data Rate: 2 GB/sec
Queue Full Threshold: 750
Topology: Direct Fabric Attach
NPort ID: 0x010400

JBOD PORT1 INFORMATION
Status: Good
Link State: Up
Port Data Rate: 2 GB/sec
-----------------------------------------------------------

No Map >




Logs ...........................................................




Slot: 0x15
Component: 0xff
Subcomponent: 0xff
Event Unique Information:
Internal disk 5 indicating fault

Entry 10
Event Type: 0x1
Sequence Number: 1825
Time Stamp: 19h:41m:20s, 11-1-2003
Module ID: 0x0b1
Controller SN: 00PR00D52487
Process ID: 0xffffffff
Slot: 0x0
Event Length: 0x28
Event Code: 0x187
Count: 0x1
Enclosure ID: 0x0
Slot: 0x1e
Component: 0xff
Subcomponent: 0xff
Event Unique Information:
Internal disk 14 indicating fault

Entry 5
Event Type: 0x1
Sequence Number: 1296
Time Stamp: 19h:37m:42s, 11-1-2003
Module ID: 0x01e
Controller SN: 00PR00D52487
Process ID: 0xffffffff
Slot: 0x0
Event Length: 0x6f
Event Code: 0x260
Count: 0x1
Enclosure ID: 0xff
Slot: 0xff
Component: 0xff
Subcomponent: 0xff
Event Unique Information:
State: 4 (NO_MAP_STATE)
Warnings:
2 (BATTERY_WARNING)
17 (STATE_CHANGING_WARNING)
22 (SNGL_CTLR_WARNING)
No Map >

[Joshua Scott]

First, Did you make sure that all of the LCCs on all of the enclosures are set to 2GB/s (I assume you are using 2GB/s fibre cards). If that doesn't solve it try this:

'No Map' means your Array is not ready. Try:

vfpmgr -R full

Then, post the output of this command:
vfpdsp -s

Josh

[Arend Lensen]

Hello Javier,

I see that you did not try help on the vfp.
It would have told you that you must specify

'YES and not only the character 'y'

after the format command :-)'

Regards,
Arend