EVA 4400 - Address test verification failure

[D. Buettner]

Hi all,

we wanted to change the configuration of an eva 4400. We uninitialised the system, shut down the system and removed two of the eight disk shelfes. After powering on again, the management modules startet but both storage controller did not.  Both controller stopped booting with an 'Address  test verification failure'. 

Here is the output of the controllers:

<BC> 01 power-up
Read MALDV0 - BOOTSTRAP_EEPROM[5] : 0xa0
Main
Module type/rev/eco: 0x1/0x4/0x0
BOOT diagnostics - Build configuration information :
Baselevel ID : CR2306
Baselevel Date : 09/09/14 10:18:01
Image built by : formal
Software Version : 11300000
Build Environment : lep
BIST TE 0xB7 - SDRAM Configuration and Policy Memory Test
-- Press CTRL-R to skip long tests --
T01: AMCC440SPe SDRAM Configuration
DIMM #0 SPD:
ADDR 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F ASCII
---- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -----
0000 80 08 08 0E 0A 61 48 00 05 30 45 06 82 08 08 00 .....aH..0E.....
0010 0C 04 38 01 01 05 03 3D 45 50 45 3C 1E 3C 2D 80 ..8....=EPE<.<-.
0020 20 27 10 17 3C 1E 1E 00 00 3C 69 80 18 22 0F 00 '..<....<i.."..
0030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 12 75 ...............u
0040 2C 00 00 00 00 00 00 00 0C 31 38 48 54 46 31 32 ,........18HTF12
0050 38 37 32 50 44 59 36 36 37 44 32 02 00 08 27 D6 872PDY667D2...'.
0060 2B 61 12 00 00 00 00 00 00 00 00 00 00 00 00 00 +a..............
0070 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
DIMM #1 SPD:
ADDR 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F ASCII
---- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -----
0000 80 08 08 0E 0A 61 48 00 05 30 45 06 82 08 08 00 .....aH..0E.....
0010 0C 04 38 01 01 05 03 3D 45 50 45 3C 1E 3C 2D 80 ..8....=EPE<.<-.
0020 20 27 10 17 3C 1E 1E 00 00 3C 69 80 18 22 0F 00 '..<....<i.."..
0030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 12 75 ...............u
0040 2C 00 00 00 00 00 00 00 0C 31 38 48 54 46 31 32 ,........18HTF12
0050 38 37 32 50 44 59 36 36 37 44 32 02 00 08 27 D6 872PDY667D2...'.
0060 2B 61 11 00 00 00 00 00 00 00 00 00 00 00 00 00 +a..............
0070 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
CACHE EEPROM part number= 18HTF12872PDY667D2
POLICY EEPROM part number= 18HTF12872PDY667D2
CACHE EEPROM serial number= 0xD62B6111 (0d3593167121)
POLICY EEPROM serial number= 0xD62B6112 (0d3593167122)
CACHE EEPROM number of ranks= 2
POLICY EEPROM number of ranks= 2
CACHE EEPROM DRAM chip size= 512 megabits
POLICY EEPROM DRAM chip size= 512 megabits
DIMM Slot 1 = 1024 MB
DIMM Slot 2 = 1024 MB
Total = 2048 MB
DQS: mid = 008 (start = 000, end = 016)
FDBK: mid = 063
Read cycle sample select = T2
SDRAM registers:
MCIF0_CODT = 0x2a800f21
MCIF0_MODT0 = 0x78000000
MCIF0_MODT1 = 0x00000000
MCIF0_MODT2 = 0x07800000
MCIF0_MODT3 = 0x00000000
MCIF0_MB0CF = 0x00000201
MCIF0_MB1CF = 0x00000201
MCIF0_MB2CF = 0x00000201
MCIF0_MB3CF = 0x00000201
MCIF0_SDTR1 = 0x80301000
MCIF0_SDTR2 = 0x42205242
MCIF0_SDTR3 = 0x0c100d1c
MCIF0_OPAR1 = 0x80000037
MCIF0_MCOPT2 = 0x08000000
MCIF0_MCOPT1 = 0x3d122000
MCIF0_RTR = 0x08200000
MCIF0_MMODE = 0x00000642
MCIF0_MEMODE = 0x00000384
MCIF0_CLKTR = 0x80000000
MCIF0_WRDTR = 0x80000820
MQ0_B0BAS = 0x2000f000
MQ0_B1BAS = 0x2800f000
MQ0_B2BAS = 0x1000f000
MQ0_B3BAS = 0x1800f000
MQ0_BAUH = 0x00000008
MQ0_CF1H = 0x80001c80
MQ0_ESH = 0x00000000
MQ0_EAUH = 0x00000000
MQ0_EALH = 0x00000000
MQ0_BAUL = 0x00000000
MQ0_CF1L = 0x80001c80
MQ0_ESL = 0x00000000
MQ0_EAUL = 0x00000000
MQ0_EALL = 0x00000000
MQ0_CFBHL = 0x10a68000
MQ0_XORBA = 0x00000000
MQ0_CF2H = 0x00000000
MCIF0_RQDC = 0x80000008
MCIF0_RDCC = 0x40000000
MCIF0_RFDC = 0x001001bf
MCIF0_VVPR = 0x00000000
MCIF0_DLCR = 0x03000067
MCIF0_ECCES = 0x00000000
MCIF0_MCSTAT = 0xa0000000
MCIF0_INITPLR0 = b5b80000
MCIF0_INITPLR1 = 82100400
MCIF0_INITPLR2 = 81020000
MCIF0_INITPLR3 = 81030000
MCIF0_INITPLR4 = 81010000
MCIF0_INITPLR5 = e4000100
MCIF0_INITPLR6 = 82100400
MCIF0_INITPLR7 = 99080000
MCIF0_INITPLR8 = 99080000
MCIF0_INITPLR9 = 99080000
MCIF0_INITPLR10 = 99080000
MCIF0_INITPLR11 = 81000642
MCIF0_INITPLR12 = 81010380
MCIF0_INITPLR13 = 81010004
MCIF0_INITPLR14 = 00000000
MCIF0_INITPLR15 = 00000000
T03: Walking 1 and 0 Address Test
***Address test verification failure!!!
*** boot error report - b7030120,20000010,20000010,38000010,b7,03,1

Any suggestions to solve this problem would be appreciated. 

Thanks

Dieter

[Yeskay]

Hi D. Buettner,

The "Address test verification failure" error is pointing to DIMM issue.

In-depth cache diagnostics are run only at power on of a controller. Normal runtime diagnostics will determine if parity errors are affecting data and lead to controller termination in advance of data inconsistency. That is why you see such a controller failure upon power on.

I would suggest that you reseat the controller DIMM and check the status. If the issue persists, replace the DIMM with spare and boot the controller.

[D. Buettner]

Hi Yeskay,

thank you for the information. We will check the dimms.

Kind regards,

Dieter