- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- HPE EVA Storage
- >
- Emu error in eva4100, hot reset?
HPE EVA Storage
1752272
Members
5550
Online
108786
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-24-2013 01:27 AM
12-24-2013 01:27 AM
Emu error in eva4100, hot reset?
Hi,
I have a disk enclosure that has and error in the Emu component.
<communicationbuses>
<bus>
<name>emuinternal</name>
<operationalstate>failed</operationalstate>
<failprediction>No</failprediction>
<state>Enabled</state>
</bus>
And the Heart Beat Led is dead.
My question is, if I do a EMU reset following:
Resetting the EMU
In some cases, the only corrective action for an EMU error is to replace the EMU. Call your
authorized service representative if this action is required. Another option is to reset the EMU using
the following procedure.
1. Firmly grasp the EMU mounting handle and pull the EMU partially out of the enclosure.
NOTE: You do not need to remove the EMU from the enclosure or disconnect the cables.
You must avoid putting any strain on the cables or connectors.
2.
Wait 30 seconds, and then push the EMU in and fully seat the element in the backplane. The
EMU should display any enclosure condition report within two minutes.
Does this cause a full lip?, does it interrup the full loop?, can I do it while the disk enclosure is in use?.
And If I have to finally replace the EMU with a new one, doy you have any procedure to follow?, an I do it while the disk enclosure is in use?,etc..
Thanks for the Help in Advanced!.
<bus>
<name>emuinternal</name>
<operationalstate>failed</operationalstate>
<failprediction>No</failprediction>
<state>Enabled</state>
</bus>
And the Heart Beat Led is dead.
My question is, if I do a EMU reset following:
Resetting the EMU
In some cases, the only corrective action for an EMU error is to replace the EMU. Call your
authorized service representative if this action is required. Another option is to reset the EMU using
the following procedure.
1. Firmly grasp the EMU mounting handle and pull the EMU partially out of the enclosure.
NOTE: You do not need to remove the EMU from the enclosure or disconnect the cables.
You must avoid putting any strain on the cables or connectors.
2.
Wait 30 seconds, and then push the EMU in and fully seat the element in the backplane. The
EMU should display any enclosure condition report within two minutes.
Does this cause a full lip?, does it interrup the full loop?, can I do it while the disk enclosure is in use?.
And If I have to finally replace the EMU with a new one, doy you have any procedure to follow?, an I do it while the disk enclosure is in use?,etc..
Thanks for the Help in Advanced!.
Windows?, no thanks
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-24-2013 03:28 PM
12-24-2013 03:28 PM
Re: Emu error in eva4100, hot reset?
Re-seating EMU will not trigger LIP. Yes it can be reseated online but make sure the Back-end cables are not touched will will obviously cause LIP.
EMU can be replaced when disk shelf is in use. just remove the cables and slide it in and connect the cables again. No special procedures are involved.
Do you see any error code in the EMU seven segment display?
EMU can be replaced when disk shelf is in use. just remove the cables and slide it in and connect the cables again. No special procedures are involved.
Do you see any error code in the EMU seven segment display?
If you feel this was helpful please click the KUDOS! star in the left column!
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP