BladeSystem - General
1748128 Members
3522 Online
108758 Solutions
New Discussion

Re: Check if i can add a hba to blade ?

 
gigiz
Valued Contributor

Check if i can add a hba to blade ?

Hi guys,

I do not know very well a blade .

i have this scenario:

 

ia64 hp Integrity BL870c i2

 # ioscan -fnCfc
Class I H/W Path Driver S/W State H/W Type Description
=====================================================================
fc 0 0/0/0/5/0/0/0 fcd CLAIMED INTERFACE HP 451871-B21 8Gb Dual Port PCIe Fibre Channel Mezzanine (FC Port 1)
/dev/fcd0
fc 1 0/0/0/5/0/0/1 fcd CLAIMED INTERFACE HP 451871-B21 8Gb Dual Port PCIe Fibre Channel Mezzanine (FC Port 2)
/dev/fcd1
fc 4 1/0/0/5/0/0/0 fcd CLAIMED INTERFACE HP 451871-B21 8Gb Dual Port PCIe Fibre Channel Mezzanine (FC Port 1)
/dev/fcd4
fc 5 1/0/0/5/0/0/1 fcd CLAIMED INTERFACE HP 451871-B21 8Gb Dual Port PCIe Fibre Channel Mezzanine (FC Port 2)
/dev/fcd5

 

I have verified and all 4 fc are used.

My customer asked me for verify if we can add any hba? 

I don't know how verify it ? 

help me 

 

 

P.S. this thread has been moved from HP-UX > General to BladeSystem > HP BladeSystem - HP Forums moderator

7 REPLIES 7
SoorajCleris
Honored Contributor

Re: Check if i can add a hba to blade ?

Hi,

 

In 870i2 there are 6 Mezenine slots.. Check the quick specs at link.

http://h18000.www1.hp.com/products/quickspecs/13620_div/13620_div.HTML

 

Infact, if you say ther are 4 FC controllers are ther you will not be able to find out what slots are populated.

There may be some NIC which is in the slot.  I didnt check deeply what slot support what card.

 

but you should verify everything before you go ahead.

 

Regards,

Sooraj

"UNIX is basically a simple operating system, but you have to be a genius to understand the simplicity" - Dennis Ritchie
Torsten.
Acclaimed Contributor

Re: Check if i can add a hba to blade ?

Your ioscan indicates you have one fibre channel mezzanine card in mezz slot 1 of both blades, so you have 2 additional cards installed.

 

Both cards are connected to interconnect bays 3 and 4.

 

I saw this from your ioscan, but you can easily see this from OA.

 

If you DON'T have FC interconnects in bays 5 - 8, you CANNOT add more FC cards.

 

 

 

Possible solutions:

 

- Put more FC interconnects in the enclosure

- upgrade the BL870ci2 to BL890ci2

- don't change anything

 

 

 

Whatever HBA (mezzanine card) you need, you need the appropriate interconnects at the back of the enclosure too.


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Matti_Kurkela
Honored Contributor

Re: Check if i can add a hba to blade ?

You already have 2x dual-port HBAs in a BL870c i2, which is a conjoined configuration of two full-height blades. Each full-height blade has three mezzanine slots.

 

The hardware paths for the existing HBAs are 0/0/0/5/* and 1/0/0/5/*, which indicates the existing HBA mezzanine cards are in mezzanine slot #1's of each component blade. Assuming that you have a c7000 chassis, these slots (and *only* these slots) are routed to I/O module slots #3 and #4 at the back of the chassis.

 

If the I/O module slots #5 .. #8 are free, you could add a new HBA mezzanine card, but you would have to buy *two* FC I/O modules to use both ports of your new HBA, as the mezzanine slots #2 and #3 are only routed to these I/O module slots. The connections are also split so that e.g. a mezzanine card in slot #2 gets its first port from I/O module #5 and the second one from I/O module #6.

 

Each I/O module provides physical connections for all the blades in the chassis, so it would be rather expensive to get new I/O modules for just 1 or 2 more FC ports... but if other blades in the same chassis also would benefit from having more HBAs, it might be worthwhile.

 

If the I/O module slots #5 .. #8 are occupied by I/O modules of another type (e.g. NIC, SAS or InfiniBand), then adding a FC mezzanine card in mezzanine slot #2 or #3 would conflict with the I/O modules, and the chassis OA would prevent the blade from powering up. In this case, the upgrade is not possible.

MK
gigiz
Valued Contributor

Re: Check if i can add a hba to blade ?

What are a command from OA to see a configuration and if i have 

a slot free for ad hba ?

S_Logan
HPE Pro

Re: Check if i can add a hba to blade ?

Hi ,
 
SHOW SERVER INFO
 
Example
OA-> show server info 11
 
More infromation:
 

Regards,

Surendar

Was the post useful?

Say Thank you by Clicking the WHITE KUDOS! Star.

For HP Guided Troubleshooting; http://www.hp.com/support/hpgt

 
I work for HPE

Accept or Kudo


[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
Torsten.
Acclaimed Contributor

Re: Check if i can add a hba to blade ?


@gigiz wrote:

What are a command from OA to see a configuration and if i have 

a slot free for ad hba ?


As said earlier, having a free slot does NOT mean you can install a mezzanine card there!

 

See comments above.

 

Once in GUI of OA, select the blade, then information or port mapping for showing related information.


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
gigiz
Valued Contributor

Re: Check if i can add a hba to blade ?

Ok thanks at all,

last one,

i want study the blade architecture for integrity in hpux .

Can you link me  a manual, cookbook and all that are good about it.

 

Thanks