General
cancel
Showing results for 
Search instead for 
Did you mean: 

Error installing HP-UX 11i v3 on bl860 i2

 
SOLVED
Go to solution
Error installing HP-UX
Occasional Visitor

Error installing HP-UX 11i v3 on bl860 i2

I am trying to install HP-UX 11.31 (September 2010) in a BL860c i2 from the DVD of c3000 enclosure, but I is presented the following error:

MFS is not defined.
krs_read_mfs: Error 5 opening MFS.
Found Adjacent data tr. Growing size. 0x1c59000 -> 0x5c59000.
Loaded ACPI revision 2.0 tables.
krs_read_mfs: Error 5 opening MFS.

*** A system crash has occurred. (See the above messages for details.)
*** The system is now preparing to dump physical memory to disk, for use
*** in debugging the crash.

ERROR: Your system crashed before I/O and dump configuration was complete.
This system does not support a crash dump under these circumstances.
Contact your HP support representative for assistance.


A level I have the following firmware versions:

Onboard Administrator: 3.11

iLO FW: 01/30/1930
System FW: 01.24
MHW FPGA: 01.14
Mon Power FW: 03.04
Front Panel HW: 04.00
PRS HW: 02.07
IOH HW: 02.02

8 REPLIES 8
Shibin_2
Honored Contributor
Solution

Re: Error installing HP-UX 11i v3 on bl860 i2

Read this thread. It is explaining the same situation and same infrastructure as yours.

http://h30499.www3.hp.com/t5/System-Administration/11-31-OS-installation-failed-with-below-error/m-p/4175709#M321768

Regards
Shibin
Error installing HP-UX
Occasional Visitor

Re: Error installing HP-UX 11i v3 on bl860 i2

Try to install from an external DVD drive to see if the same error occurs
Torsten.
Acclaimed Contributor

Re: Error installing HP-UX 11i v3 on bl860 i2

>> init of hardware not successful


Do you have mezzanine cards installed?

Check them (properly installed, supported, etc) and consider to try the installation without the cards.

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
nijokj
Trusted Contributor

Re: Error installing HP-UX 11i v3 on bl860 i2

I am posting a supporting doc from HP for BL860 boot failure.
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c02104557〈=en&cc=us&taskId=101&prodSeriesId=4186437&prodTypeId=3709945
INH
Regular Advisor

Re: Error installing HP-UX 11i v3 on bl860 i2


Hi,

ensure the firmware on the new blades is also current. The BL860c i2 requires firmware bundle 15.05. The BL460c G7 depends on the OS installed. Refer to http://h20000.www2.hp.com/bizsupport/TechSupport/DriverDownload.jsp?prodNameId=4194638〈=en&cc=us&prodTypeId=3709945&prodSeriesId=4194735&taskId=135
for further details.

HTH

Regds,
INH
Knowledge is power
INH
Regular Advisor

Re: Error installing HP-UX 11i v3 on bl860 i2

What i mean is check for supported and recemended firmware. I2 blade require a certian level of firmware to be in place at enclousre level as well as blade level

Regards,
INH
Knowledge is power
Error installing HP-UX
Occasional Visitor

Re: Error installing HP-UX 11i v3 on bl860 i2

This error was resolved by updating the firmware version Onboard Administrator to version 3.21, settled with the DVD that comes ADDED in c3000 and the installation media to HP-UX 11.31 September 2010
Error installing HP-UX
Occasional Visitor

Re: Error installing HP-UX 11i v3 on bl860 i2

Used versions:

Onboard Administrator: 3.21

iLO FW: 01/30/1930
System FW: 01.24
MHW FPGA: 01.14
Mon Power FW: 03.04
Front Panel HW: 04.00
PRS HW: 02.07
IOH HW: 02.02

HP-UX 11.31 September 2010