HBA problems

[Linoge]

Good day to all!
I have a problem with qlogic 2340 (firmware 1.47) and RHEL 3 (2.4.21-4). I got this messages when I tryed to get LUN on EMC CLARiiON

qla2x00_set_info starts at address = f88f0060
PCI: Enabling device 03:03.0 (0000 -> 0003)
qla2x00: Found VID=1077 DID=2312 SSVID=1077 SSDID=100
scsi(1): Found a QLA2312 @ bus 3, device 0x3, irq 3, iobase 0xf899d000
scsi(1): 64 Bit PCI Addressing Enabled.
scsi(1): Allocated 4096 SRB(s).
scsi(1): Configure NVRAM parameters...
scsi(1): Verifying loaded RISC code...
scsi(1): Verifying chip...
scsi(1): Waiting for LIP to complete...
scsi(1): LIP reset occurred.
scsi(1): LIP occurred.
scsi(1): LOOP UP detected.
scsi(1): Port database changed.
scsi(1): Topology - (Loop), Host Loop address 0x7d
qla2x00_detect num_hosts=0
PCI: Enabling device 04:04.0 (0000 -> 0003)
qla2x00: Found VID=1077 DID=2312 SSVID=1077 SSDID=9
scsi(2): Found a QLA2312 @ bus 4, device 0x4, irq 3, iobase 0xf899f000
scsi(2): 64 Bit PCI Addressing Enabled.
scsi(2): Allocated 4096 SRB(s).
scsi(2): Configure NVRAM parameters...
scsi(2): Verifying loaded RISC code...
scsi(2): Verifying chip...
scsi(2): Waiting for LIP to complete...
scsi(2): LIP reset occurred.
scsi(2): LIP occurred.
scsi(2): LOOP UP detected.
scsi(2): Port database changed.
scsi(2): Topology - (Loop), Host Loop address 0x0
qla2x00_detect num_hosts=1
scsi-qla0-adapter-port=210000e08b137c45\;
scsi-qla0-tgt-0-di-0-node=50060160b0222355\;
scsi-qla0-tgt-0-di-0-port=5006016030222355\;
scsi-qla0-tgt-0-di-0-control=00\;
scsi-qla0-tgt-0-di-0-preferred=ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff\;
scsi-qla1-adapter-port=210000e08b139c4e\;
scsi-qla1-tgt-0-di-1-node=50060160b0222355\;
scsi-qla1-tgt-0-di-1-port=5006016830222355\;
scsi-qla1-tgt-0-di-1-control=80\;
scsi1 : QLogic QLA2312 PCI to Fibre Channel Host Adapter: bus 3 device 3 irq 3
Firmware version: 3.03.01, Driver version 7.01.01-fo

scsi2 : QLogic QLA2312 PCI to Fibre Channel Host Adapter: bus 4 device 4 irq 3
Firmware version: 3.03.01, Driver version 7.01.01-fo

Starting timer : 0 0
blk: queue c940ec18, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
qla2xxx_eh_abort scsi(1:0:0:0): cmd_timeout_in_sec=0x6.
qla2x00(1): Performing ISP error recovery - ha= f69a4100.
scsi(1): Waiting for LIP to complete...
scsi(1): LIP reset occurred.
scsi(1): LIP occurred.
scsi(1): LOOP UP detected.
scsi(1): Port database changed.
scsi(1): Topology - (Loop), Host Loop address 0x7d
qla2xxx_eh_abort Exiting: status=Failed
scsi(1:0:0:0): DEVICE RESET ISSUED.
scsi(1:0:0:0): DEVICE RESET SUCCEEDED.
qla2xxx_eh_abort scsi(1:0:0:0): cmd_timeout_in_sec=0x6.
qla2x00(1): Performing ISP error recovery - ha= f69a4100.
scsi(1): Waiting for LIP to complete...
scsi(1): LIP reset occurred.
scsi(1): LIP occurred.
scsi(1): LOOP UP detected.
scsi(1): Port database changed.
scsi(1): Topology - (Loop), Host Loop address 0x7d
qla2xxx_eh_abort Exiting: status=Failed
scsi(1:0:0:0): LOOP RESET ISSUED.
scsi(1): LIP reset occurred.
qla2xxx_eh_bus_reset(1): reset succeded
scsi(1): LOOP DEAD detected.
qla2x00: FAILOVER device 0 from 5006016030222355 -> 5006016830222355 - LUN 00, reason=0x1
qla2x00: FROM HBA 0 to HBA 1
scsi: device set offline - not ready or command retry failed after bus reset: host 1 channel 0 id 0 lun 0

I have done:
1) Change firmware (from 1.29 to 1.50 --- hba didn't detect LOOP!!!)
2) Change firmware (from 1.50 to 1.47 -- hba detect LOOP)

[Linoge]

Just foget =)

This HBA (only with firmware 1.47) work perfectly in win2k3 Enterprice, SUSE 10 (2.6.16).