1748183 Members
3507 Online
108759 Solutions
New Discussion юеВ

Re: HP-UX does not boot

 
mahbub
Advisor

HP-UX does not boot

Dear all,

I am facing rp3440 server boot problem. Also unable to access BCH mode.

Processor is booting from the first available device.

To discontinue, press any key within 10 seconds.

I tried several times to discontinue by pressing any key but failed to access BCH mode.

finallay the below message showed
INIT: Command is respawning too rapidly.
Will try again in 5 minutes.
Check for possible errors.
id:ems4 "/etc/opt/resmon/lbin/p_client"

INIT: Command is respawning too rapidly.
Will try again in 5 minutes.
Check for possible errors.
id:cim1 "/opt/wbem/lbin/cimserverd"

INIT: Command is respawning too rapidly.
Will try again in 5 minutes.
Check for possible errors.
id:util "/usr/lbin/utild # Utilization Provider daemon"

I am attaching error message.

Any body help me to fix the problem.

Thanks and regards
Mahbub
28 REPLIES 28
Michael Steele_2
Honored Contributor

Re: HP-UX does not boot

HI

Go back to the BCH, yes, that's what your attachement says, you were in the GSP, and 'bo alt'.

Did you mirror your boot disks?

Your problem appears to be the /etc/inittab file, did you modifity this file?

If not, what did you change in /etc?

You can also boot to single user. You can also boot to the old kernel.
Support Fatherhood - Stop Family Law
Dennis Handly
Acclaimed Contributor

Re: HP-UX does not boot

It appears that /usr/bin/, etc. aren't mounting.
mahbub
Advisor

Re: HP-UX does not boot

Dear

Unable to access BCH mode.

To discontinue, press any key within 10 seconds.

I tried several times to discontinue by pressing any key but failed to access BCH mode.

How I will access the BCH mode?

Best regards
Mahbub
Michael Steele_2
Honored Contributor

Re: HP-UX does not boot

HI

Can you control b and get to the GSP menu like in your attachement?

When you see the 'discontinue' message, I believe you're still seeing firmware generated messages, and this would indicate a system or gsp board. I believe they are two separate boards, with the GSP piggy backing onto the system board.

If you can't get back to the GSP with the control b command then I'm assuming a HW failure.

However, I have never seen or heard nor can I find any reference to this 'can not access the BCH error'.
Support Fatherhood - Stop Family Law
mahbub
Advisor

Re: HP-UX does not boot

Dear,

Yes, I able to access BCH mode.
Please see the below information:

vlnboot
sh: vlnboot: not found
# lvlnboot -v
lvlnboot: Volume group not activated.
Cannot display volume group "/dev/vg00".
lvlnboot: Volume group not activated.
Cannot display volume group "/dev/vgtst".
lvlnboot: Volume group not activated.
Cannot display volume group "/dev/vgbkp".
# lvlnbfsck /dev/vg00/lvol3
vxfs fsck: Cannot open /dev/vg00/lvol3: No such device or address
file system check failure, aborting ...
# fsck /dev/vg00/lvol4
vxfs fsck: Cannot open /dev/vg00/lvol4: No such device or address
file system check failure, aborting ...
# bdf
sh: bdf: not found
# lvlnboot -R
lvlnboot: Warning: couldn't query physical volume "/dev/dsk/c2t0d0":
The specified path does not correspond to physical volume attached to
this volume group
lvlnboot: Warning: couldn't query physical volume "/dev/dsk/c2t1d0":
The specified path does not correspond to physical volume attached to
this volume group
lvlnboot: Warning: couldn't query all of the physical volumes.
lvlnboot: Warning: couldn't query physical volume "/dev/dsk/c6t0d1":
The specified path does not correspond to physical volume attached to
this volume group
lvlnboot: Warning: couldn't query physical volume "/dev/dsk/c8t0d1":
The specified path does not correspond to physical volume attached to
this volume group
lvlnboot: Warning: couldn't query physical volume "/dev/dsk/c6t0d2":
The specified path does not correspond to physical volume attached to
this volume group
lvlnboot: Warning: couldn't query physical volume "/dev/dsk/c6t0d3":
The specified path does not correspond to physical volume attached to
this volume group
lvlnboot: Warning: couldn't query physical volume "/dev/dsk/c6t0d4":
The specified path does not correspond to physical volume attached to
this volume group
lvlnboot: Warning: couldn't query physical volume "/dev/dsk/c8t0d2":
The specified path does not correspond to physical volume attached to
this volume group
lvlnboot: Warning: couldn't query physical volume "/dev/dsk/c8t0d3":
The specified path does not correspond to physical volume attached to
this volume group
lvlnboot: Warning: couldn't query physical volume "/dev/dsk/c8t0d4":
The specified path does not correspond to physical volume attached to
this volume group
lvlnboot: Warning: couldn't query all of the physical volumes.
lvlnboot: Warning: couldn't query physical volume "/dev/dsk/c6t0d5":
The specified path does not correspond to physical volume attached to
this volume group
lvlnboot: Warning: couldn't query physical volume "/dev/dsk/c6t0d6":
The specified path does not correspond to physical volume attached to
this volume group
lvlnboot: Warning: couldn't query physical volume "/dev/dsk/c8t0d5":
The specified path does not correspond to physical volume attached to
this volume group
lvlnboot: Warning: couldn't query physical volume "/dev/dsk/c8t0d6":
The specified path does not correspond to physical volume attached to
this volume group
lvlnboot: Warning: couldn't query all of the physical volumes.
vgcfgbackup: Warning: couldn't query physical volume "/dev/dsk/c6t0d5":
The specified path does not correspond to physical volume attached to
this volume group
vgcfgbackup: Warning: couldn't query physical volume "/dev/dsk/c6t0d6":
The specified path does not correspond to physical volume attached to
this volume group
vgcfgbackup: Warning: couldn't query physical volume "/dev/dsk/c8t0d5":
The specified path does not correspond to physical volume attached to
this volume group
vgcfgbackup: Warning: couldn't query physical volume "/dev/dsk/c8t0d6":
The specified path does not correspond to physical volume attached to
this volume group
vgcfgbackup: Warning: couldn't query all of the physical volumes.
vgcfgbackup: Volume group not activated.


What will be next step? Please comment-----.


Best regards
Mahbub
Michael Steele_2
Honored Contributor

Re: HP-UX does not boot

did you boot off the alt or the pri? single user or all the way up? Are any disks bad? Use 'dd=/dev/dsk/c t d of=/dev/null count=100'. What does i/oscan say? What does syslog.log say.

You got to know some of this? Start debugging.
Support Fatherhood - Stop Family Law
Vishu
Trusted Contributor

Re: HP-UX does not boot

Hi,

Well, i think you are in maintenance mode or something where your VGs are not activated and you are trying to retrieve the information and getting those errors.

Try booting in single user mode and then try to mount your FS by activating all VGs and see if you have any bad disk in a particular VG which inhibits it from activating.

Regarding your first post, your error seems to come from /etc/inittab. Also, check for the same in that file.
Michael Steele_2
Honored Contributor

Re: HP-UX does not boot

What is

'who -r'
Support Fatherhood - Stop Family Law
mahbub
Advisor

Re: HP-UX does not boot

Dear all,

# diskinfo /dev/rdsk/c2t0d0
sh: diskinfo: not found
# strings /etc/lvmtab
sh: strings: not found
# vgdisplay -v vg00
--- Volume groups ---
VG Name /dev/vg00
VG Write Access read/write
VG Status available
Max LV 255
Cur LV 11
Open LV 11
Max PV 16
Cur PV 2
Act PV 2
Max PE per PV 4384
VGDA 4
PE Size (Mbytes) 32
Total PE 8748
Alloc PE 7746
Free PE 1002
Total PVG 0
Total Spare PVs 0
Total Spare PVs in use 0

--- Logical volumes ---
LV Name /dev/vg00/lvol1
LV Status available/syncd
LV Size (Mbytes) 320
Current LE 10
Allocated PE 20
Used PV 2

LV Name /dev/vg00/lvol2
LV Status available/syncd
LV Size (Mbytes) 4096
Current LE 128
Allocated PE 256
Used PV 2

LV Name /dev/vg00/lvol3
LV Status available/syncd
LV Size (Mbytes) 256
Current LE 8
Allocated PE 16
Used PV 2

LV Name /dev/vg00/lvol4
LV Status available/syncd
LV Size (Mbytes) 6016
Current LE 188
Allocated PE 376
Used PV 2

LV Name /dev/vg00/lvol5
LV Status available/syncd
LV Size (Mbytes) 10016
Current LE 313
Allocated PE 626
Used PV 2

LV Name /dev/vg00/lvol6
LV Status available/syncd
LV Size (Mbytes) 4032
Current LE 126
Allocated PE 252
Used PV 2

LV Name /dev/vg00/lvol7
LV Status available/syncd
LV Size (Mbytes) 2560
Current LE 80
Allocated PE 160
Used PV 2

LV Name /dev/vg00/lvol8
LV Status available/syncd
LV Size (Mbytes) 4608
Current LE 144
Allocated PE 288
Used PV 2

LV Name /dev/vg00/lvol9
LV Status available/syncd
LV Size (Mbytes) 30016
Current LE 938
Allocated PE 1876
Used PV 2

LV Name /dev/vg00/lvol10
LV Status available/syncd
LV Size (Mbytes) 50016
Current LE 1563
Allocated PE 3126
Used PV 2

LV Name /dev/vg00/lvol11
LV Status available/syncd
LV Size (Mbytes) 12000
Current LE 375
Allocated PE 750
Used PV 2


--- Physical volumes ---
PV Name /dev/dsk/c2t0d0
PV Status available
Total PE 4374
Free PE 501
Autoswitch On

PV Name /dev/dsk/c2t1d0
PV Status available
Total PE 4374
Free PE 501
Autoswitch On

# ioscan -fnC disk
Class I H/W Path Driver S/W State H/W Type Description
==========================================================================
disk 0 0/0/2/0.0.0.0 sdisk CLAIMED DEVICE TEAC DV-28E-N
/dev/dsk/c0t0d0 /dev/rdsk/c0t0d0
disk 1 0/1/1/0.0.0 sdisk CLAIMED DEVICE HP 146 GST3146707LC
/dev/dsk/c2t0d0 /dev/rdsk/c2t0d0
disk 2 0/1/1/0.1.0 sdisk CLAIMED DEVICE HP 146 GST3146707LC

# df
sh: df: not found
# bdf
sh: bdf: not found
# string /ec
sh: string: not found
# string /etc/lvmtab
sh: string: not found


HP-UX Start-up in progress
__________________________


VxVM general startup ................................................ OK
.................................................................... FAIL
*
Mount file systems .................................................. FAIL
*

Setting hostname .................................................... FAIL
*

Enable auxiliary swap space ......................................... FAIL
*

Configure Loopback interfaces (lo0) ................................. FAIL
*

Configuring all unconfigured software filesets ...................... FAIL
*
R
Configure HP igelan Gigabit Ethernet interfaces ..................... FAIL
*
Configure HP iether Gigabit Ethernet interfaces ..................... FAIL
*
Configure HP Gigabit Ethernet interfaces ............................ FAIL
*
Configure HP Ethernet interfaces .................................... FAIL
*

Configure LAN interfaces ............................................ FAIL
*
Start name server daemon ............................................ FAIL
*

Start NFS core subsystem ............................................ FAIL
*

Configuring PPP Interface ........................................... FAIL
*

Starting mail daemon ................................................ FAIL
*

Start SNMP Master Network Management daemon ......................... FAIL
*

Start SNMP HP-UNIX Network Management subAgent ...................... FAIL
*
Start SNMP MIB-2 Network Management subAgent ........................ FAIL
*
Start SNMP Trap Dest Network Management subAgent .................... FAIL
*
S
Start SNMP PCI FDDI Network Management subAgent ..................... FAIL
*

Initialize Instant Capacity ......................................... FAIL
*
.................................................................... FAIL
*

Starting HP Disk Array Manager daemons. ............................. FAIL
*
Starting disk array monitor daemons. ................................ FAIL
*

Start USB hub daemon ................................................ FAIL
*

Initialize Software Distributor agent daemon ........................ FAIL
*

Start EMS SNMP subagent ............................................. FAIL
*
Configure HP Fibre Channel Mass Storage interfaces .................. FAIL
*
Configure HP Internal RAID interfaces ............................... FAIL
*
Configuring Ultra320 SCSI Mass Storage interfaces ................... FAIL
*

preter "/usr/bin/sh" not found
FAIL *
Configure HP Fibre Channel Tachyon TL/TS Mass Storage interfaces .... FAIL
*
Configuring HP Fibre Channel FCD Mass Storage interfaces ............ FAIL
*
VVR - Starting Communication Daemon ................................. N/A
.................................................................... inter
preter "/bin/sh" not found
file link resolves to "/usr/bin/sh"
FAIL *
.................................................................... inter
preter "/bin/sh" not found
file link resolves to "/usr/bin/sh"
FAIL *
.................................................................... inter
preter "/bin/sh" not found
file link resolves to "/usr/bin/sh"
FAIL *
S
Start CDE login server .............................................. FAIL
*


* - An error has occurred !
* - Refer to the file /etc/rc.log for more information.



The system is ready.

INIT: Command is respawning too rapidly.
Will try again in 5 minutes.
Check for possible errors.
id:cim1 "/opt/wbem/lbin/cimserverd"

INIT: Command is respawning too rapidly.
Will try again in 5 minutes.
Check for possible errors.
id:cons "/usr/sbin/getty console console # system console"

INIT: Command is respawning too rapidly.
Will try again in 5 minutes.
Check for possible errors.
id:util "/usr/lbin/utild # Utilization Provider daemon"

INIT: Command is respawning too rapidly.
Will try again in 5 minutes.
Check for possible errors.
id:ems4 "/etc/opt/resmon/lbin/p_client"


Please inform me what will i do?

Best regards
Mahbub