- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- High LUNs in HP-UX
Operating System - HP-UX
1753943
Members
9282
Online
108811
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-26-2004 10:35 PM
тАО12-26-2004 10:35 PM
High LUNs in HP-UX
Hi
We have a target device connected to a SAN.
I have noticed that HPUX can work with LU numbers 0-7.
LUNs higher than 7 can not be accessed by HPUX.
I have also noticed that if i define LUN 0 as raid device (0xC) then i receive a scsi report LUNs command from the HPUX however only LUNs 0-7 are being accessed.
How can i make HPUX access LUNs higher than 7?
Are there some specific flags in Inquiry or inquiry page 80h they i should set?
Do i need inquiry page 80h at all?
Thanks,
Michael
We have a target device connected to a SAN.
I have noticed that HPUX can work with LU numbers 0-7.
LUNs higher than 7 can not be accessed by HPUX.
I have also noticed that if i define LUN 0 as raid device (0xC) then i receive a scsi report LUNs command from the HPUX however only LUNs 0-7 are being accessed.
How can i make HPUX access LUNs higher than 7?
Are there some specific flags in Inquiry or inquiry page 80h they i should set?
Do i need inquiry page 80h at all?
Thanks,
Michael
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-26-2004 10:53 PM
тАО12-26-2004 10:53 PM
Re: High LUNs in HP-UX
Michael,
There has been some discussion in this forum on the same subject, please review the link below and that should throw some light
http://forums1.itrc.hp.com/service/forums/questionanswer.do?admit=716493758+1104148235194+28353475&threadId=47921
regards
Mobeen
There has been some discussion in this forum on the same subject, please review the link below and that should throw some light
http://forums1.itrc.hp.com/service/forums/questionanswer.do?admit=716493758+1104148235194+28353475&threadId=47921
regards
Mobeen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-27-2004 12:44 AM
тАО12-27-2004 12:44 AM
Re: High LUNs in HP-UX
If there is no disk assigned on lun0 hp-ux typically detects the disk array itself as a disk. Except its not a disk and can generate EMS errors.
The rule of thumb in the past for LUN's higher than 7 is yes, on HP disk arrays.
I have been waiting several years for a patch that will allow hp-ux to access lun numbers above 7 on non-hp disk arrays.
It probably depends on your disk array vendor how many luns are assignable.
SEP
The rule of thumb in the past for LUN's higher than 7 is yes, on HP disk arrays.
I have been waiting several years for a patch that will allow hp-ux to access lun numbers above 7 on non-hp disk arrays.
It probably depends on your disk array vendor how many luns are assignable.
SEP
Steven E Protter
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-27-2004 02:19 AM
тАО12-27-2004 02:19 AM
Re: High LUNs in HP-UX
Hi Michael,
Maybe this link will help,
http://www2.itrc.hp.com/service/cki/docDisplay.do?docLocale=en_US&docId=200000072399697
The itrc doc id is KBRC00010719.
Hope this helps.
Regds
Maybe this link will help,
http://www2.itrc.hp.com/service/cki/docDisplay.do?docLocale=en_US&docId=200000072399697
The itrc doc id is KBRC00010719.
Hope this helps.
Regds
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP