- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- How to change monitor's resolution?
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-09-2011 02:04 PM
12-09-2011 02:04 PM
How to change monitor's resolution?
Hello
Does anyone know how to change console monotor's resolution?
I use netbackup GUI of rx2660 via X server emulator on 1024*768 note pc,
I can not see bottom/top of some netbackup's windows , because rx2660's resolution is 1280*1024 but note pc 1024*768.
How to change monitor's resolution?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-10-2011 03:02 PM
12-10-2011 03:02 PM
Re: How to change monitor's resolution?
If you're using an X server on your notebook PC, then the resolution of the rx2660's console has no effect to your situation at all. Your remote X session is not a duplicate of the session on the console, but a completely independent session.
You should check the settings of your X server emulator: a good X server emulator should automatically detect the resolution of the PC, unless it's been configured to use something else. Even a bad X server emulator should have some way to adjust the resolution of the virtual X desktop.
But the real problem might be the Netbackup GUI itself: the designers of Netbackup probably haven't even considered if their application GUI is useable with a display resolution that was common back in 1995 or so - more than 15 years ago.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-12-2011 04:26 AM
12-12-2011 04:26 AM
Re: How to change monitor's resolution?
Hi,
You can try the below two options if its an X server:
1. Open /etc/X11/xorg.conf using a text editor (pico /etx/X11/xorg.conf) and add these two lines in the Monitor section of the config file:
HorizSync 31-95
VertRefresh 50-60
Now reboot X or your server and next time you connect using VNC you'll be able to select up to 1024x768.
The Monitor Section will look something like this when you have added the two lines:
Section "Monitor"
Identifier "Configured Monitor"
HorizSync 31-95
VertRefresh 50-60
EndSection
2. Open /etc/X11/xorg.conf and modify the subsection "Display" section to look something like below (the first mode you give is the default it takes)
DefaultDepth 24
SubSection “Display”
Virtual 1024 768
Depth 24
Modes “1024x768@60” “800x600@60”
EndSubSection
Chhaya
I am an HP employee.
Was this post useful? - You may click the KUDOS! star to say thank you.