Installing HP-UX + SUPERDOME

[CowBoy]

Dear All
Hi
I have a superdome and i want to install HP-UX on it.
I Ordered a SCSI DVD Reader and i have an EVA4000 but I don't know how can i install HP-UX
and how can i present A LUN before installing HP-UX ???

[Torsten. · Accepted solution]

First connect to the switch and create a (port based) zone. Then boot from the installer dvd. After the initial scan done by the installer, the eva is aware of your server. Create a vdisk and present. Now let the installer scan the hardware again.
The installer will now see the disk - ready to proceed with installation...

[vjta]

Hi,
are there any local disks attached to ur SD.

regards
vjta

[CowBoy]

The problem is that there is no HDD attache to the SD...
I 'll give you the information after i test the EVA!!!
thank you in advance

[CowBoy]

Dear All
eventually i boot my server from a External SCSI and both SCSI and Fiber(from EVA) are detected bu i faced this error
Please help me Friends
Thanks
##########################################
EFI Boot Manager ver 1.10 [14.61] Please select a boot option

DVD
HP-UX Primary Boot: 0/0/1/0/1.8.0
EFI Shell [Built-in]
Boot Option Maintenance Menu


Use ^ and v to change option(s). Use Enter to select an option
Use > and < to view long descriptions
Hot Key: 'S' or 's' to start the EFI Shell

Selected boot option: DVD

Loading.: DVD

Load of DVD failed: Not Found

Press any key to continue
##################################

[CowBoy]

PS:both the DVDROM and DVD are OK but it can not load the WININSTALL...

[Ramaprasad K]

Hi MSN,

I suppose you have not followed the 'crystal clear' steps suggested by Torsten.

Once you configure Switch(note: u would need WWN no of HBA on SD, which you can find from shell), by zoning or otherwise, the disks are seen by server on which the OS will be installed when you boot from your CD/DVD.

Ram

[CowBoy]

Hi there
I did the torlsten steps but my problem is that the DVDROM can not load the DVD1 of HP-ux 11.23 boot file...
I do sure the DVDROM and The DVDROM don't have any problem...

[Ramaprasad K]

Hi MSN,

Try using another DVD as it clearly says
'Load of DVD failed: Not Found'.

Check if you can read DVD on another server or PC, if so, try changing Drive.

Regards,
Ram

[Alastair Donaldson]

The EVA will need to know the WWID of your HBA. You can get this from your SAN Switch. Also The EVA may well auto detect the WWID.

Add the host to the EVA using the correct WWID then add some LUN's and present them to the host. This is all done on the EVA.

It is also possible that the DVD option in your EFI boot menu is not pointing to the correct location. When your system powers up you should see output similar to the following. (this was done on an rx8640 so it will be somewhat different).

Broadcom NetXtreme Gigabit Ethernet (BCM5703) is detected (PCI-X)
Scsi(Pun6,Lun0) HP 300 GST3300007LC HPC1 (320 MBytes/sec)
Scsi(Pun2,Lun0) Optiarc DVD RW AD-5170A 1.32 ( 40 MBytes/sec)
Scsi(Pun6,Lun0) HP 300 GST3300007LC HPC1 (320 MBytes/sec)
Scsi(Pun0,Lun0) HP C7438A V601 ( 40 MBytes/sec)
POSSE Library is loading...
EFI Shell version 1.10 [14.61]
Device mapping table
fs0 : Acpi(HWP0002,PNP0A03,0)/Pci(2|0)/Scsi(Pun6,Lun0)/HD(Part1,Sig7DEC5FF4-)
fs1 : Acpi(HWP0002,PNP0A03,0)/Pci(2|0)/Scsi(Pun6,Lun0)/HD(Part3,Sig7DEC6026-)
fs2 : Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)/CDROM(Entry0)
blk0 : Acpi(HWP0002,PNP0A03,0)/Pci(2|0)/Scsi(Pun6,Lun0)
blk1 : Acpi(HWP0002,PNP0A03,0)/Pci(2|0)/Scsi(Pun6,Lun0)/HD(Part1,Sig7DEC5FF4-)
blk2 : Acpi(HWP0002,PNP0A03,0)/Pci(2|0)/Scsi(Pun6,Lun0)/HD(Part2,Sig7DEC6012-)
blk3 : Acpi(HWP0002,PNP0A03,0)/Pci(2|0)/Scsi(Pun6,Lun0)/HD(Part3,Sig7DEC6026-)
blk4 : Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)
blk5 : Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)/CDROM(Entry0)
blk6 : Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)/CDROM(Entry1)
blk7 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)

Note where your DVD drive is then drop into the EFI Shell from the boot options menu. In this case the DVD is fs2.

EFI Shell version 1.10 [14.61]
Device mapping table
fs0 : Acpi(HWP0002,PNP0A03,0)/Pci(2|0)/Scsi(Pun6,Lun0)/HD(Part1,Sig7DEC5FF4-)
fs1 : Acpi(HWP0002,PNP0A03,0)/Pci(2|0)/Scsi(Pun6,Lun0)/HD(Part3,Sig7DEC6026-)
fs2 : Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)/CDROM(Entry0)
blk0 : Acpi(HWP0002,PNP0A03,0)/Pci(2|0)/Scsi(Pun6,Lun0)
blk1 : Acpi(HWP0002,PNP0A03,0)/Pci(2|0)/Scsi(Pun6,Lun0)/HD(Part1,Sig7DEC5FF4-)
blk2 : Acpi(HWP0002,PNP0A03,0)/Pci(2|0)/Scsi(Pun6,Lun0)/HD(Part2,Sig7DEC6012-)
blk3 : Acpi(HWP0002,PNP0A03,0)/Pci(2|0)/Scsi(Pun6,Lun0)/HD(Part3,Sig7DEC6026-)
blk4 : Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)
blk5 : Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)/CDROM(Entry0)
blk6 : Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)/CDROM(Entry1)
blk7 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)

startup.nsh> echo -off

setting hpux path(\EFI\HPUX)...
type 'fs[x]:' where x is your bootdisk (0, 1, 2...)
type 'hpux' to start hpux bootloader

From the shell select the DVD drive the cd into the efi\boot directory

Shell> fs2:
fs2:\> ls
Directory of: fs2:\

01/10/06 05:19p 1,024 EFI
01/10/06 05:19p 541,306 INSTALL.EFI
01/10/06 05:19p 16 AUTO
01/10/06 05:19p 174 STARTUP.NSH
3 File(s) 541,496 bytes
1 Dir(s)


fs2:\> cd efi

fs2:\EFI> ls
Directory of: fs2:\EFI

01/10/06 05:19p 1,024 .
01/10/06 05:19p 0 ..
01/10/06 05:19p 1,024 BOOT
01/10/06 05:19p 1,024 Intel_Firmware
01/10/06 05:19p 1,024 HP
0 File(s) 0 bytes
5 Dir(s)


fs2:\EFI> cd boot

fs2:\EFI\BOOT> ls
Directory of: fs2:\EFI\BOOT

01/10/06 05:19p 1,024 .
01/10/06 05:19p 1,024 ..
01/10/06 05:19p 541,306 BOOTIA64.EFI
01/10/06 05:19p 16 AUTO
2 File(s) 541,322 bytes
2 Dir(s)


fs2:\EFI\BOOT> bootia64.efi

(C) Copyright 2004 Hewlett-Packard Development Company, L.P.All rights reserved

HP-UX Boot Loader for IPF -- Revision 2.027

Press Any Key to interrupt Autoboot
\EFI\BOOT\AUTO ==> boot :IINSTALL