- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - Linux
- >
- Installing and Configuring
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-06-2007 06:36 PM
тАО03-06-2007 06:36 PM
Installing and Configuring
i Just want to install FC6 on Raid 5 with a HPNetRaid D4943-60002.
First of all i configured a volume (Raid 5) with three Disk (3x Seagate 150176LC) an initialized it = everything fine
Then i installed FC6 = everything works
I just modified some conf files and reboot the system
After rebooting the are a lot of errors and the disks were detekted separately (fdisk -l shows three disks, sda sdb sdc, sda has 100GB and the others only 50GB)
While booting i get an error for the Partitiontable something with P3...
Now i just thougt about updatating the bios from A04.00 to A04.03. But when i start to update (started with a DRDOS Disk) the programm tells me that this programm cannot be run in DOS mode. How can do the update?
And some other questions
When i start the system in Rescue mode everthing is fine and there is only sda shown with fdisk.
I read in another thread for debian that there should be a problem while loading megaraid and aic7xxx parallel. I just diabled the onboard aic7800 in bios, but i don't know how to disable it in the kernel cause the system still tries to load the module aic7xxx. i think this is the problem.
are there any solutions for my problems?
i hope my describing is understandable cause my english is not very well.
thanks for answering and greetz from germany
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-06-2007 08:02 PM
тАО03-06-2007 08:02 PM
Re: Installing and Configuring
First, you have detailed out the problem very well and in defined manner, at least I didn't face any problem in understanding it..
It seems you have done some configuration errors, and I think it's not related to firmware (though it's always good to have latest firmware).
Pls check & recall which are the files you have done config chages, and then it would be easier for you to troubleshoot.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-07-2007 04:48 AM
тАО03-07-2007 04:48 AM
Re: Installing and Configuring
now in the evening i just restart the system to get an actual error log to post...while the system reboots i get an error for hdb, this is an extension disk whith only data, its on the ide port and hasn't produced any errors yet. cause there is sensitive data on it i disabled the disk and reboot...this time no errors from the megaraid appears only network doesn't work
though you can see what happens i post the error log in the following link
http://nopaste.linux-dev.org/?1290
now i think there is something wrong with the motherboard cause there are new errors that have never been before..i will now try to reboot the system with hdb active and see what happens this time.
at the end i just ask again for the firmware update, cause i don't know how to do the update..inside linux and dos it doesn't work
thanks eric
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-07-2007 06:04 AM
тАО03-07-2007 06:04 AM
Re: Installing and Configuring
I don't see a problem with what you've done except playing around with the bios settings.
In general a few things need to be understood.
1) FC6 is not producgtion grade software, especially for servers. The yum update probably introduced some bad code into the system that caused this problem. I'm using FC6 to connect to ITRC right now.
2) Storage setup needs to be finalized prior to configuration. That means you get the storage working the way you want and then put in filesystems and logical volumes and whatnot.
3) The best way out of this if the system isn't already to corrupt for recovery is to boot from the previous kernel.
SEP
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-08-2007 05:24 PM
тАО03-08-2007 05:24 PM
Re: Installing and Configuring
current version is now A04.03, this is the most actual version i found...
i hope that this is/was the problem...i bootet the system three times and it works
i will try on an post the results if there are still errors
thanks for this time
bye eric