- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - Linux
- >
- P600 Redhat Linux - hpacucli "Slot Unknown"
Operating System - Linux
1753774
Members
6957
Online
108799
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-01-2007 06:23 PM
07-01-2007 06:23 PM
P600 Redhat Linux - hpacucli "Slot Unknown"
Hi all ,
Recently i implemented new P600 on Redhat 3 .
But i am getting unknown slot error which
i can't continue with array setup .
lsmod shows csiss loaded .
The card attached to IBM Xseries .
Could someone advice
=> ctrl all show detail
Smart Array P600
Bus Interface: PCI
Slot: Slot Unknown
Serial Number: P92B30F9ST014L
Cache Serial Number: P67570R9SUK068
RAID 6 (ADG) Status: Enabled
RAID 6 (ADG) Enabler Status: Enabled
Controller Status: OK
Chassis Slot:
Hardware Revision: Rev A
Firmware Version: 1.52
Rebuild Priority: Medium
Expand Priority: Medium
Surface Scan Delay: 0 sec
Cache Board Present: True
Cache Status: Not Configured
Accelerator Ratio: 50% Read / 50% Write
Total Cache Size: 256 MB
Battery Pack Count: 2
Battery Status: OK
SATA NCQ Supported: False
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-01-2007 07:35 PM
07-01-2007 07:35 PM
Re: P600 Redhat Linux - hpacucli "Slot Unknown"
Hi,
I've never used a P600 or an IBM X series, however I'd guess that the hpacucli doesn't include any programming to be able to read the PCI configuration of a non-HP server...
Cheers,
Rob
I've never used a P600 or an IBM X series, however I'd guess that the hpacucli doesn't include any programming to be able to read the PCI configuration of a non-HP server...
Cheers,
Rob
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP