- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - Microsoft
- >
- Question about HP4 printers
Operating System - Microsoft
1748073
Members
5063
Online
108758
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-03-2000 05:17 AM
03-03-2000 05:17 AM
Question about HP4 printers
Is there any way to prevent the HP4M printer (with HP JetDirect card) from
propogating IPX traffic on a network?
We are using JetAdmin v2.53 and it only gives you two options for protocol
traffic behaviour - Novell (IPX/SPX) and All. Is there perhaps an updated
JetAdmin program that allows you the option of including/excluding individual
protocols?
- Mike
propogating IPX traffic on a network?
We are using JetAdmin v2.53 and it only gives you two options for protocol
traffic behaviour - Novell (IPX/SPX) and All. Is there perhaps an updated
JetAdmin program that allows you the option of including/excluding individual
protocols?
- Mike
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-03-2000 09:15 AM
03-03-2000 09:15 AM
Re: Question about HP4 printers
Mike,
You may need to flash the firmware on your JetDirect card. Doing this enables
the JetDirect card to use more than IPX/SPX. Other protocols available are
TCP/IP and DLC. On some models AppleTalk is also available. The firmware
upgrade is a must if you want the JetDirect card to do more. Advice for doing
this upgrade:
1. Do this on the same network segment. Make sure you are not going across a
router else this simple firmware flash will become very difficult.
2. Do this when there is not too much network traffic.
Hope this helps you out,
---Gerard
You may need to flash the firmware on your JetDirect card. Doing this enables
the JetDirect card to use more than IPX/SPX. Other protocols available are
TCP/IP and DLC. On some models AppleTalk is also available. The firmware
upgrade is a must if you want the JetDirect card to do more. Advice for doing
this upgrade:
1. Do this on the same network segment. Make sure you are not going across a
router else this simple firmware flash will become very difficult.
2. Do this when there is not too much network traffic.
Hope this helps you out,
---Gerard
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP