- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- When I chaneg netmask ifconfig and spee lanadmin w...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-16-2002 12:25 AM
тАО08-16-2002 12:25 AM
When I chaneg netmask ifconfig and spee lanadmin which files should be edited
which files should be modified after that.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-16-2002 12:27 AM
тАО08-16-2002 12:27 AM
Re: When I chaneg netmask ifconfig and spee lanadmin which files should be edited
For netmask /etc/rc.config.d/netconf
For speed, it depends on which driver your lancard is using, you can check by doing ioscan -fknClan and then match it to this list;
Driver duplex file Description Software
btlan hpbtlanconf
btlan0 hpeisabtconf
btlan1 hpbasetconf
btlan3 hpbase100conf Internal (core) LAN card
btlan4 hpgsc100conf
btlan5 hppci100conf "external" PCI card A5230A
btlan6 hpsppci100conf V-class PCI lan card
gelan hpgelanconf GigaBit card A4926A
All the files are in /etc/rc.config.d
If youre going to do it online you should test it from the console by doing /sbin/init.d/net stop then start.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-16-2002 01:01 AM
тАО08-16-2002 01:01 AM
Re: When I chaneg netmask ifconfig and spee lanadmin which files should be edited
lan 0 10/4/4.1 lan3 CLAIMED INTERFACE
/dev/diag/lan0 /dev/ether0 /dev/lan0
lan 1 10/12/6 lan2 CLAIMED INTERFACE Built-in LAN
/dev/diag/lan1 /dev/ether1
lan 2 10/16/8 btlan1 UNCLAIMED UNKNOWN HP HP-PB 100 Base TX car
What if it is lan3 or lan2 which file?
Thanks in advnance
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-16-2002 02:44 AM
тАО08-16-2002 02:44 AM
Re: When I chaneg netmask ifconfig and spee lanadmin which files should be edited
#lan0:
IP_ADDRESS[0]=4.3.2.1
SUBNET_MASK[0]=255.255.255.0
INTERFACE_NAME[0]=lan0
BROADCAST_ADDRESS[0]=4.3.2.255
INTERFACE_STATE[0]=up
DHCP_ENABLE[0]=0
ROUTE_DESTINATION[0]="default"
ROUTE_MASK[0]=""
ROUTE_GATEWAY[0]=gateway
ROUTE_COUNT[0]=1
#lan1:
IP_ADDRESS[1]=4.3.2.2
SUBNET_MASK[1]=255.255.255.0
INTERFACE_NAME[1]=lan1
BROADCAST_ADDRESS[1]=4.3.2.255
INTERFACE_STATE[1]=up
DHCP_ENABLE[1]=0
ROUTE_DESTINATION[1]="default"
ROUTE_MASK[1]=""
ROUTE_GATEWAY[1]=gateway
ROUTE_COUNT[1]=1
... and any other interfaces, based on what is in the [] brackets.
I'm not sure, but I believe the card speed is set up in /etc/rc.config.d/hpbase100conf
Cheers!
James
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-20-2002 03:57 AM
тАО08-20-2002 03:57 AM
Re: When I chaneg netmask ifconfig and spee lanadmin which files should be edited
speed is in bits, I believe
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-20-2002 04:12 AM
тАО08-20-2002 04:12 AM
Re: When I chaneg netmask ifconfig and spee lanadmin which files should be edited
For your btlan1 card (HP-PB 100 Base TX product; #A3495A) you should set the speed to "100FD". This turns off auto-negotiation. This setting is made in '/etc/rc.config.d/hpbasetconf' on pre 11.11 servers and in '/etc/rc.config.d/hpbtlanconf' on 11.11.
Regards!
...JRF...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-20-2002 04:18 AM
тАО08-20-2002 04:18 AM
Re: When I chaneg netmask ifconfig and spee lanadmin which files should be edited
You need to edit two files:
/etc/rc.config.d/netconf - netmask
/etc/rc.config.d/hpbasetconf- speed of 100BT lan card.
hth