- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - Linux
- >
- Re: diskless proliant ML370 g3 - SAN booting with ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-30-2004 01:37 AM
тАО01-30-2004 01:37 AM
A diskless proliant server with two hbas
(FCA 2214) should be able to boot from a MA8000
with securepath 3.0b enabled.
The linux distribution is SuSE SELS 8 with
service pack 2a.
We have success without Securepath.
But when securepath will be started at init
the system freezes :(
Anyone with tips or a running diskless server?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-30-2004 02:28 AM
тАО01-30-2004 02:28 AM
Re: diskless proliant ML370 g3 - SAN booting with secure path
There needs to be drivers and those are OS specific. If you are off the certification Matrix, get back on and try again.
An example I'm familiar with.
Red Hat AS 2.1 is certified by HP with certain disk arrays and server combinations. That works. Take the same server and put Red Hat AS 3.0 on it and it does not work because HP doesn't have drivers that work yet on their servers.
SEP
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-30-2004 03:31 AM
тАО01-30-2004 03:31 AM
Re: diskless proliant ML370 g3 - SAN booting with secure path
ftp://ftp.compaq.com/pub/products/storageworks/techdoc/san/AA-RV1AB-TE.pdf
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-01-2004 09:16 PM
тАО02-01-2004 09:16 PM
Re: diskless proliant ML370 g3 - SAN booting with secure path
Is SecurePath supported on a diskless
server?
booting from san was not the point.
the problem is initrd and securepath.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-02-2004 09:31 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-02-2004 06:57 PM
тАО02-02-2004 06:57 PM
Re: diskless proliant ML370 g3 - SAN booting with secure path
could i say the following to my customer:
SecurePath on a diskless Server is not
supportet at the time.
Please put the os on local scsi disks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-03-2004 01:05 AM
тАО02-03-2004 01:05 AM