Skip to ContentSkip to Footer
Start of content
- Community Home
- >
- Servers and Operating Systems
- >
- Operating System - Linux
- >
- General
- >
- does qlogic driver 7 on RHEL3 U2 i386 support MSA1...
General
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Latin America
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
12-27-2004 04:11 AM
12-27-2004 04:11 AM
does qlogic driver 7 on RHEL3 U2 i386 support MSA1000 F200?
Hi,
I have a customer running rhel3 u2 i386 on Proliant systems. They're tring to connect two systems(each with two FCA2214) to MSA1000 dual controller + dual B series SAN switches with qla2300 v7.01.01. I think is is a HP supported config(from qla2300 release notes), but the customer can't failover luns.
They see 'FAIL OVER FROM ... To ...' in dmesg but just lost the LUNs. Sb. said SSP should be enabled for Linux failover, I don't know where does this comment come from, but will try tomorrow. But anybody can confirm this configuration is supported?
Thanks a lot!
Tommy
I have a customer running rhel3 u2 i386 on Proliant systems. They're tring to connect two systems(each with two FCA2214) to MSA1000 dual controller + dual B series SAN switches with qla2300 v7.01.01. I think is is a HP supported config(from qla2300 release notes), but the customer can't failover luns.
They see 'FAIL OVER FROM ... To ...' in dmesg but just lost the LUNs. Sb. said SSP should be enabled for Linux failover, I don't know where does this comment come from, but will try tomorrow. But anybody can confirm this configuration is supported?
Thanks a lot!
Tommy
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
End of content
United States
Hewlett Packard Enterprise International
Communities
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP