- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: how to set Gigabit interfaces strictly to 1000...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-17-2009 01:18 AM
тАО05-17-2009 01:18 AM
and I would like to set the speed of the interfaces strictly to 1000FD and disable autoneg.
when trying to do it using SAM.I recieve this error "speed value cannot be set to 1000,when autoneg is off"
I checked the /etc/rc.config.d/hp*conf files and for speed value 1000fd is not an option.
so Is it possible to do so.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-17-2009 01:42 AM
тАО05-17-2009 01:42 AM
Re: how to set Gigabit interfaces strictly to 1000FD on HP-UX v2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-17-2009 04:21 AM
тАО05-17-2009 04:21 AM
Re: how to set Gigabit interfaces strictly to 1000FD on HP-UX v2
lanadmin -s 0
lanadmin -s 1
-x will give you both the speed and autoneg.
#lanadmin -x 0
Speed = 1000 Full-Duplex.
Autonegotiation = On.
to set the speed use S ( uppercase S, this will NOT work in 11.11)
lanadmin -S 0 1000000000
or
lanadmin -speed 0 (you can set in MBITS/sec only in 11.23)
lanadmin -X 0 ( this will NOT work in 11.11)
Thanks
Basheer
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-17-2009 06:21 AM
тАО05-17-2009 06:21 AM
Re: how to set Gigabit interfaces strictly to 1000FD on HP-UX v2
HP recommands to set autoneg=ON on both switch and card side for gigabit cards. Otherwise card may not get the desired link and speed
Ganesh.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-17-2009 06:16 PM
тАО05-17-2009 06:16 PM
SolutionThis is not just a recommendation, it is mandatory for *all* Gigabit connections per the industry specification. The LAN cards will always autonegotiate to 1000FD as long as the switch and cables will support that speed. If the cards do not select 1000FD, then the other end does not support 1000FD or is misconfigured.
Bill Hassell, sysadmin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-19-2009 11:44 PM
тАО05-19-2009 11:44 PM
Re: how to set Gigabit interfaces strictly to 1000FD on HP-UX v2
So The summary that it is impossible.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-20-2009 08:38 AM
тАО05-20-2009 08:38 AM