- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- io not starting
Operating System - HP-UX
1753850
Members
7493
Online
108807
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-23-2006 04:54 AM
11-23-2006 04:54 AM
I have an rp7410 , after connecting electricity, i turned on the cabinet : pe -- t -- on . then turned on the cell: pe -- c -- 1 -- on . when i try to turn on the io, it will take me to cm but without booting the io.
the server have one cell in cell 1 and 2 io in io 0 and io 1. i am not getting any errors. how to proceed?
if i try to create a genesis partition i will get: RtnCodeIOBayNotAttachedToCell
the server have one cell in cell 1 and 2 io in io 0 and io 1. i am not getting any errors. how to proceed?
if i try to create a genesis partition i will get: RtnCodeIOBayNotAttachedToCell
Solved! Go to Solution.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-23-2006 05:52 AM
11-23-2006 05:52 AM
Solution
Hi, Simon, to create a genesis partition you have to make sure that the cell you chose must be connected to an I/O chassis. The I/O chassis must have a core I/O card installed,
and it should have a bootable disk (or a method for installing an operating system and a disk onto
which it can be installed).
I hope you have read "HP System Partitions Guide". Anyway, here is the link for that doc:
http://docs.hp.com/en/5991-1247/5991-1247.pdf
Yang
and it should have a bootable disk (or a method for installing an operating system and a disk onto
which it can be installed).
I hope you have read "HP System Partitions Guide". Anyway, here is the link for that doc:
http://docs.hp.com/en/5991-1247/5991-1247.pdf
Yang
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP