- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - Linux
- >
- Re: monitoring
Operating System - Linux
1753317
Members
5389
Online
108792
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-22-2003 12:43 PM
тАО05-22-2003 12:43 PM
monitoring
I am running redhat 7.3 on DL 380 with smart array 5i controller the raid 5 disks are in external compaq storage works 4300 box , Please advise me how can i monitor the disks so that if any disk fails or any thing wrong with the logical drive it should inform me. I tried removing a disk from the array and the driver reported nothing in proc or syslog or dmesg. even the compaq 4300 didn't made any beep , it just turned a small red light on .
Cheers
Bobby
Cheers
Bobby
bobby
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-23-2003 11:34 AM
тАО05-23-2003 11:34 AM
Re: monitoring
Thanks for your reply, Well, you can configure the syslog.conf to get the messages at the specified place. Going a level below i.e. how the message is generated in the first instance . The smart array 5i card should trigger the drive failure first. If we talk about storageworks 4300 . The fault bus signal (SWAP) detects the removal or insertion of storeage device on a SCSI bus , causing the signal to generate a logic low pulse. This pulse is detected by EMU and an amber light is glown . unfortunately there is no beep sound. That was my first question is it done deleberately (design) or something broken in my hardware.
syslog will only get message if the driver will generate anything that was my second question why the cciss does not generate any error when the drive is removed . I guess there is some sort of monitoring utility (SNMP or something that logs the error conditon in proc or syslog) that Compaq provides. Getting that utility was the ultimate goal of this posting .
cheers
Bobby
syslog will only get message if the driver will generate anything that was my second question why the cciss does not generate any error when the drive is removed . I guess there is some sort of monitoring utility (SNMP or something that logs the error conditon in proc or syslog) that Compaq provides. Getting that utility was the ultimate goal of this posting .
cheers
Bobby
bobby
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-25-2003 09:48 PM
тАО05-25-2003 09:48 PM
Re: monitoring
Bobby,
You can find the latest HP/Compaq software and drivers for a DL380 running RH Linux 7.3 here:
http://h18007.www1.hp.com/support/files/server/us/locate/86_4706.html
Have you installed the ProLiant Support Pack? The package includes "health" agents that monitor various subsystems:
http://h18007.www1.hp.com/support/files/server/us/download/10931.html
-Jared
You can find the latest HP/Compaq software and drivers for a DL380 running RH Linux 7.3 here:
http://h18007.www1.hp.com/support/files/server/us/locate/86_4706.html
Have you installed the ProLiant Support Pack? The package includes "health" agents that monitor various subsystems:
http://h18007.www1.hp.com/support/files/server/us/download/10931.html
-Jared
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-26-2003 05:57 AM
тАО05-26-2003 05:57 AM
Re: monitoring
Install the Proliant management agents, and health drivers. Then you can set up your favorite management software to receive SNMP traps for hardware events generated by your management agents.
Rgds Jarle
Rgds Jarle
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP