- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - Linux
- >
- Re: network configuration
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-14-2001 07:14 PM
тАО10-14-2001 07:14 PM
I have only one Ether card and I have to switch between Internet and intranet IP's. I know how to change IP's using netcfg. But what I would like to know is how can I do it from the "#" prompt without GUI. WHich files should be changed and what are the commands I have to run along with syntax.
If somebody can tell me it would be most helpfull. It would also be helpful if somebody can tell me how to change IP's on an OPENBSD machine.
Thankx
trent
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-14-2001 10:21 PM
тАО10-14-2001 10:21 PM
SolutionIf you are using RedHat (or similar) distribution, your network configuration is stored under
/etc/sysconfig.
See /etc/sysconfig/network and /etc/sysconfig/network-script/ifcfg-eth0
and /etc/hosts, /etc/resolv.conf are also important.
Regards,
masanari iida
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-15-2001 01:20 AM
тАО10-15-2001 01:20 AM
Re: network configuration
-Santosh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-15-2001 02:15 AM
тАО10-15-2001 02:15 AM
Re: network configuration
Hope somebody can answer my OPenbsd question.
Trent
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-15-2001 09:18 PM
тАО10-15-2001 09:18 PM
Re: network configuration
Run 'man hostname.if' and 'man afterboot' for instructions.
Timo Rajala
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-15-2001 09:51 PM
тАО10-15-2001 09:51 PM
Re: network configuration
(Aliases) that way, when you switch the cable, it should work automaticly.
It is not a clean solution, but a laisy one :)