- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - Linux
- >
- Re: problem msa 1000
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2006 08:02 PM
тАО09-07-2006 08:02 PM
problem msa 1000
the results:i can see 3 luns correcltly and 3 luns (the same ) unitialized.
when i run disk managment i receive a messagge about the 3 luns unitialized.
If i try to initialize its, i can't do it
could someone help me?
p.s. i have already installed the last support pack 7.51 and updated the fw of the msa to 4,48 and i use the mpio vers. 2.0
thanks gigi
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2006 10:11 PM
тАО09-07-2006 10:11 PM
Re: problem msa 1000
the three unitialized LUNs are your already connected LUNs, but seen over the seconds path / controller. It seems that you MPIO setup doesn├В┬┤t working.
Regards,
Patrick
Patrick
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2006 10:22 PM
тАО09-07-2006 10:22 PM
Re: problem msa 1000
I think that your right about my problem.
But when i try to install MPIO i receive a message about the upgrade of my array controller 5i.
It seems trying to install MPIO on the array controller on board and not to HBA.
If i confirm it in the scsi device i can see the mpio device but evethinks doesn't perform correctly.
gigi
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2006 10:47 PM
тАО09-07-2006 10:47 PM
Re: problem msa 1000
try to uninstall MPIO completely and reboot your server. Then try to install MPIO again. Please don't use MPIO v2.0, cause this is for EVA only. Use MPIO v1.20 (HP MPIO Basic DSM (Device Specific Module) for Windows for MSA1000/MSA1500 Active-Passive Disk Arrays). You can download it under the following URL:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=421495&prodTypeId=18964&prodSeriesId=421492&swLang=13&taskId=135&swEnvOID=1005
Regards,
Patrick
Patrick
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-08-2006 12:07 AM
тАО09-08-2006 12:07 AM
Re: problem msa 1000
I've already tryed to uninstall mpio reboot server and use the mpio version 1.2 but i can't see any results.
i have the same problems with both nodes
I don't understand why mpio tryes to install over on-board array controller.
I've already installed other msa 1000 without this problems.
thanks gigi
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-08-2006 12:38 AM
тАО09-08-2006 12:38 AM
Re: problem msa 1000
what HBAs are you using? Windows 2000 Advanced Server or did you use Windows Server 2003 Enterprise? Did you upgrade the HBAs drivers?
Regards,
Patrick
Patrick
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-08-2006 12:44 AM
тАО09-08-2006 12:44 AM
Re: problem msa 1000
I'm using w2k3 enterprise, hba emulex lp950 and I've already upgraded the hba's drivers with psp 7.51 and their fw
gigi
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-08-2006 01:00 AM
тАО09-08-2006 01:00 AM
Re: problem msa 1000
maybe another forum member have an idea... Did you meet the requirements according to the MPIO readme, especially the needed version of the storport driver?
Regards,
Patrick
Patrick