- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: FAILURE DETECTED
HPE 9000 and HPE e3000 Servers
1752677
Members
5910
Online
108789
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-26-2009 09:45 AM
08-26-2009 09:45 AM
I have the below message on all my cell boards..
what does this mean..
With the below fault can I install OS on the server & create a Virtual host & a Guest
HW status for Cell 0 : FAILURE DETECTED
Power status : on, CPU 0 MODULE FAULT
Faults above are latched. They are cleared just before the cell is powered on.
Boot is not blocked
PDH memory is shared
Processor Compatibility : OK
RIO cable status : connected
what does this mean..
With the below fault can I install OS on the server & create a Virtual host & a Guest
HW status for Cell 0 : FAILURE DETECTED
Power status : on, CPU 0 MODULE FAULT
Faults above are latched. They are cleared just before the cell is powered on.
Boot is not blocked
PDH memory is shared
Processor Compatibility : OK
RIO cable status : connected
Solved! Go to Solution.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-26-2009 09:51 AM
08-26-2009 09:51 AM
Solution
David,
To check parstatus and see how many cpu you can see per cell board. Or is there anything missing.
Also check with top how many cpu.
It looks like you have a bad cpu or a cpu that is failing.
Also to check with
GSP-->CM-->PS
GSP-->CM-->DF -->Specific fru --> select CPU.
to check current cpu status,
Hth,
Raj.
To check parstatus and see how many cpu you can see per cell board. Or is there anything missing.
Also check with top how many cpu.
It looks like you have a bad cpu or a cpu that is failing.
Also to check with
GSP-->CM-->PS
GSP-->CM-->DF -->Specific fru --> select CPU.
to check current cpu status,
Hth,
Raj.
" If u think u can , If u think u cannot , - You are always Right . "
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP