- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Server not running after reboot
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-10-2006 08:08 PM
тАО09-10-2006 08:08 PM
Server not running after reboot
we have 2 rp7420 servers in cluster. we did some modification to the volume group and and installed online JFS that required reboot. one node is up and running and the other is not.
I login to the MP and found the partition and cell is off. I coundn't bring it up with MP>PE command
here some of the output:
MP:CM> bo
This command boots the selected partition.
Part# Name
----- ----
0) Partition 0
Select a partition number: 0
Do you want to boot partition number 0? (Y/[N]) y
-> The selected partition will be booted.
Sorry, command failed: RtnCodeNoPoweredCellSlotsInPartition
then MP>PS
HW status for Cell 1 : FAILURE DETECTED
Power status : NOT VIABLE, no fault
Boot is blocked
PDH memory is not shared
Processor Compatibility : FAULT
RIO cable status : UNDEFINED
RIO cable connection physical location : cannot be determined
Core cell is INVALID
Attention Led is off
PDHC status Leds : ----
CPU Module Slot 0 1 2 3
Populated
Local 48V Good
Power Enabled
Power Good
(* - True, P - Processor, T - Terminator)
DIMMs populated:
0 . . . 4 . . . 8 . . .12 . . .
1 1 1 1 1 1
VRM's 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
Present :
Enabled :
Pwr Good :
Front Side Bus Freq. : 250 MHz
CPU Core Freq. : 0 MHz
CPU Type :
System Boot Rom (SFW) firmware rev 0.000
PDH controller (PDHC) firmware rev 0.000, built THU JAN 01 00:00:00 1970
MICE revision is 0.0
please, help?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-11-2006 08:34 AM
тАО09-11-2006 08:34 AM
Re: Server not running after reboot
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-11-2006 10:40 AM
тАО09-11-2006 10:40 AM
Re: Server not running after reboot
MP -> CM -> DE
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-12-2006 06:02 PM
тАО09-12-2006 06:02 PM
Re: Server not running after reboot
we solve the power issue by unpluging the power cables and then plug them again. the server started after that normally
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-12-2006 06:02 PM
тАО09-12-2006 06:02 PM