- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: how do i do parmodify for rp8400
HPE 9000 and HPE e3000 Servers
1752580
Members
3007
Online
108788
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-01-2009 11:55 PM
12-01-2009 11:55 PM
how do i do parmodify for rp8400
I have already installed my rp8400 with hpux b11.11. Cell details are as shown bellow
MP:CM> du
The following MP bus devices were found:
+---+----+-----+-------+-------+-----------+
| | | | | | |
| | | Sys | | IO | Bulk Pwr |
|Cab| MP |Bkpln| Cells |Chassis| Supplies |
| # |M S| |0 1 2 3| 0 1 |0 1 2 3 4 5|
+---+----+-----+-------+-------+-----------|
| 0 |* *| * |* * | * * |* * * * * |
+---+----+-----+-------+-------+-----------+
MP:CM> cp
--------------
Cabinet | 0 |
--------+----+
Slot |0123|
--------+----+
Part 0 |.*..|
MP:CM>
i want to add all the cells and I/O s to this partetion. what should be the command i have to type
parmodify -p 0 -a ? :? ?
please guide me .
Thanks.
MP:CM> du
The following MP bus devices were found:
+---+----+-----+-------+-------+-----------+
| | | | | | |
| | | Sys | | IO | Bulk Pwr |
|Cab| MP |Bkpln| Cells |Chassis| Supplies |
| # |M S| |0 1 2 3| 0 1 |0 1 2 3 4 5|
+---+----+-----+-------+-------+-----------|
| 0 |* *| * |* * | * * |* * * * * |
+---+----+-----+-------+-------+-----------+
MP:CM> cp
--------------
Cabinet | 0 |
--------+----+
Slot |0123|
--------+----+
Part 0 |.*..|
MP:CM>
i want to add all the cells and I/O s to this partetion. what should be the command i have to type
parmodify -p 0 -a ? :? ?
please guide me .
Thanks.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-02-2009 01:51 AM
12-02-2009 01:51 AM
Re: how do i do parmodify for rp8400
Hi
From the OS can you run the command and give the Outputs of the same.
#parstatus
the basic idea is
#parmodify -p 0 -a:base:y:ri -a :base:y:ri -a :base:y:ri
then perform an RR that is Reboot-for-Reconfig. but please dp paste an O/p for the command parstatus as run from the server. #shutdown -Ry 0
regards | | |
From the OS can you run the command and give the Outputs of the same.
#parstatus
the basic idea is
#parmodify -p 0 -a
then perform an RR that is Reboot-for-Reconfig.
but please dp paste an O/p for the command parstatus as run from the server.
#shutdown -Ry 0
regards
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP