- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: unable to boot a v2500 running 11.11
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-09-2009 11:35 PM
тАО10-09-2009 11:35 PM
Re: unable to boot a v2500 running 11.11
Try to boot manually and see what error you are getting:
- Else , then Try with Single user mode.
from PDC:
MAin:Menu:> path
MAin:Menu:> boot
Interact with ISL, N
Check any error message,
Hth,
Raj.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-11-2009 05:58 AM
тАО10-11-2009 05:58 AM
Re: unable to boot a v2500 running 11.11
If we specify the hardware path from bch comes with no lif area.
bo pri
we reinstalled from DVD to a disk on jamaica box connected and the installation was successful. but when we boot it comes to bch and does not see a disk.
your help is much appreciated.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-11-2009 08:57 AM
тАО10-11-2009 08:57 AM
Re: unable to boot a v2500 running 11.11
And I see absolutly nothing about your LCD Error Codes! Refer to the front panel, what is there?
For example,
LED Fault Symptoms Corrective action
03 FPGA not OK 1. Core Utilities Board (SCUB)
monitoring utilities chip
(MUC) problem.
2. MUC cannot get correct
program transfer from
EEPROM on power up.
├в ┬в Cycle the node power
using the Key switch.
├в ┬в Call the Response
Center.
04 dc OK error
(Upper Left)
1. Power supply is reporting
failure (dc OK) after
keyswitch is turned on, but
prior to SCUB power on
sequence.
2. This is the first of two or more
supplies reporting failure.
Call the Response Center
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2009 07:44 AM
тАО10-12-2009 07:44 AM
Re: unable to boot a v2500 running 11.11
thank you all
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2009 07:46 AM
тАО10-12-2009 07:46 AM
Re: unable to boot a v2500 running 11.11
- « Previous
-
- 1
- 2
- Next »