HP 9000
cancel
Showing results for 
Search instead for 
Did you mean: 

Console and the rp2470

Grayh
Trusted Contributor

Console and the rp2470

I have connected through a SUV cable to my laptop to connect to the console.And then I start the hypertermal and unable to connect to it either using com2/com3/telnet.

???
7 REPLIES
Steven E. Protter
Exalted Contributor

Re: Console and the rp2470

Shalom,

You might be able to connect a null modem cable to your windows based laptop and use hyperterminal to gain console control of your system.

The system has a lan console as well which is a better option

SEP
Steven E Protter
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
Grayh
Trusted Contributor

Re: Console and the rp2470

Hi Steven,

How do i connect to the lan console...
and which cable should I use for that

I do not have the IP address of the GSP Card...
IS there a way to get the GSP IP from the OS logs...

Thanks in advance
Grayh
Trusted Contributor

Re: Console and the rp2470

i telnet to it and the session gets disconnected after every 10 minutes
Court Campbell
Honored Contributor

Re: Console and the rp2470

if you are connecting to the MP via the console, you might have to use something other than the hyperterminal. I have a few machines where hyperterminal doesn't work. I ended up using tera term.
"The difference between me and you? I will read the man page." and "Respect the hat." and "You could just do a search on ITRC, you don't need to start a thread on a topic that's been answered 100 times already." Oh, and "What. no points???"
Grayh
Trusted Contributor

Re: Console and the rp2470

That gives me a clue...

But when I connect to the server remotly... the session gets disconnected every 10 minutes and I will have to reboot the server.

looks like some time out issues...
Grayh
Trusted Contributor

Re: Console and the rp2470

Actually I noticed the pins of the A5191-63001 cable were bent...

replacing it resolved the Issue


Torsten.
Acclaimed Contributor

Re: Console and the rp2470

"the session gets disconnected every 10 minutes and I will have to reboot the server.
"

regarding the disconnect:
(taken from a similar system, not the same)

HE li

==== GSP Help ============================================(Administrator)===
AC : Alert display Configuration MS : Modem Status
AR : Automatic System Restart config. PC : Remote Power Control
CA : Configure asynch/serial ports PG : PaGing parameter setup
CL : Console Log- view console history PS : Power management module Status
CG : Certificate Generator RS : Reset System through RST signal
CO : COnsole- return to console mode SDM : Set Display Mode (hex or text)
CSP : Connect to remote Service Proc. SE : SEssion- log into the system
DC : Default Configuration SL : Show Logs (chassis code buffer)
DI : DIsconnect remote or LAN console SNMP: Set SNMP state & community string
EL : Enable/disable LAN/WEB access SO : Security options & access control
ER : Enable/disable Remote/modem SS : System Status of proc. modules
EX : Exit GSP and disconnect TC : Reset via Transfer of Control
HE : Display HElp for menu or command TE : TEll- send a msg. to other users
IT : Inactivity Timeout settings VFP : Virtual Front Panel display
LC : LAN configuration WHO : Display connected GSP users
LS : LAN Status XD : Diagnostics and/or Reset of GSP
MR : Modem Reset XU : Upgrade the GSP Firmware



Note this:

IT : Inactivity Timeout settings


But you never need to reboot the server for this!

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!