- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- HP RP3440 Voltage Fault with Flashing Red
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-20-2014 11:10 PM
07-20-2014 11:10 PM
HP RP3440 Voltage Fault with Flashing Red
I have a HP rp3440 but I can not boot with Flashing Red. When I access to MP port to view System Log with following details:
Log Entry 1: 18 Jul 2014 03:22:34
Alert Level 7: Fatal
Keyword: Type-02 020706 132870
Voltage Fault
Logged by: Baseboard Management Controller;
Sensor: Voltage - Power Good
Data1: transition to Non-recoverable
0x2053C892FA020020 00000607D6020300
Log Entry 2: 18 Jul 2014 03:22:48
Alert Level 2: Informational
Keyword: Type-02 127003 1208323
Chassis Control request to BMC via IPMI or sensor
Logged by: Baseboard Management Controller;
Sensor: System Event
Data2: OEM Code2: 0x07
0x2053C89308020030 0781A37000120300
I also checked Power Status but status was ok:
MP:CM> PS
PS
System Power state: Off
Temperature : Normal
Power supplies State
---------------------------------------------------------
Power Supply 1 Normal
Power Supply 2 Normal
Fans State
---------------------------------------------------------
Cooling 1 (Sys) Normal
Cooling 2 (Mem) Normal
Cooling 3 (Disk) Normal
Please help me what's problem with my server.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-31-2014 02:11 PM
07-31-2014 02:11 PM
Re: HP RP3440 Voltage Fault with Flashing Red
What this is saying is that the sensor that checks for overall system power is reporting a failure. What this doesnt say is what the actual cause is.
If there are no other entries in the log then you will have to bring the system down to a minimal configuration (one PS, no PCI cards, one CPU in slot 0, and no DIMMs). If that works (it will fail with no memory, but should power on) then you can build it back up until you find a problem.
If that doesnt work, then try swapping out the Power Supply with the other one, trying each slot. Next try the same with the CPU and power pod if you have another.
If all fails you may have a bad system board.
Good luck!
Bob
Was this helpful? Like this post by giving me a thumbs up below!