HP 9000
cancel
Showing results for 
Search instead for 
Did you mean: 

rp2470.... removal & replacing of CPU

Grayh
Trusted Contributor

rp2470.... removal & replacing of CPU

***Remove the CPU assembly socket by pressing the four (two on each side) tabs holding the socket to the
CPU heat sink base. The CPU chip may come off with the socket or stay attached to the heat sink.
(Usually the CPU chip stays in the socket.)****

How will remove the socket.. Only the heat sink has come out...
8 REPLIES
Torsten.
Acclaimed Contributor

Re: rp2470.... removal & replacing of CPU

What makes you sure to have a bad cpu?

http://forums.itrc.hp.com/service/forums/questionanswer.do?threadId=1265230

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Grayh
Trusted Contributor

Re: rp2470.... removal & replacing of CPU

It is reflected in the GSP>PS and the GSP>Sl logs... So had to replace...
Torsten.
Acclaimed Contributor

Re: rp2470.... removal & replacing of CPU

"It is reflected in the GSP>PS ..."


Unlikely!

Please post more information!

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Grayh
Trusted Contributor

Re: rp2470.... removal & replacing of CPU

Symptoms:Server shut's down very frequently

GSP>
************* SYSTEM ALERT **************
SYSTEM NAME: uninitialized
DATE: 09/03/2008 TIME: 15:02:38
ALERT LEVEL: 6 = Boot possible, pending failure - action required

REASON FOR ALERT
SOURCE: 6 = platform
SOURCE DETAIL: 3 = cabinet fan SOURCE ID: 0
PROBLEM DETAIL: 4 = fan failure

LEDs: RUN ATTENTION FAULT REMOTE POWER
ON FLASH OFF ON ON
LED State: There was a system interruption that did not take the system down.
Check Chassis and Console Logs for error messages.

0x002000646300405F 00000000 00000000 - type 0 = Data Field Unused
0x582008646300405F 00006C08 030F0226 - type 11 = Timestamp 09/03/2008 15:02:38
A: ack read of this entry - X: Disable all future alert messages
Anything else skip redisplay the log entry
->Choice:A
*****************************************

************* SYSTEM ALERT **************
SYSTEM NAME: uninitialized
DATE: 09/03/2008 TIME: 15:02:53
ALERT LEVEL: 6 = Boot possible, pending failure - action required

REASON FOR ALERT
SOURCE: 6 = platform
SOURCE DETAIL: 3 = cabinet fan SOURCE ID: 0
PROBLEM DETAIL: 4 = fan failure

LEDs: RUN ATTENTION FAULT REMOTE POWER
ON FLASH OFF ON ON
LED State: There was a system interruption that did not take the system down.
Check Chassis and Console Logs for error messages.

0x002000646300405F 00000000 00000000 - type 0 = Data Field Unused
0x582008646300405F 00006C08 030F0235 - type 11 = Timestamp 09/03/2008 15:02:53
A: ack read of this entry - X: Disable all future alert messages
Anything else skip redisplay the log entry

And So I had to replace it...

***Now to assess the GSP remotely what has to be done***
Torsten.
Acclaimed Contributor

Re: rp2470.... removal & replacing of CPU

OK, this is the fan mounted on CPU 0.

I assume your system goes down due to overtemp.

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Grayh
Trusted Contributor

Re: rp2470.... removal & replacing of CPU

Torston How can I assess the GSP remotely

Torsten.
Acclaimed Contributor

Re: rp2470.... removal & replacing of CPU

You need to assign an IP address

GSP> lc

and connect a cable.

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Grayh
Trusted Contributor

Re: rp2470.... removal & replacing of CPU

thank you