부팅시 셀프테스트 하면서 뿌리는 로그입니다..

[권성준]

장비는 a400 이구요..

어떤로그인지 확인해주세요..

로그를 없앨수 있는 방법과... 왜 로그를 뿌리는지 등등..





processor test 1152

processor test 1139

processor test 113A

processor test 113B

processor test 113C

processor test 113D

processor test 113E

processor INIT 1701

processor test 1120

processor test 1142

processor test 113B

platform test 612A



***** EARLY BOOT VFP : SYSTEM ALERT *****

SYSTEM NAME: GSPHP

DATE: 01/26/2005 TIME: 02:42:06

ALERT LEVEL: 6 = Boot possible, pending failure - action required



REASON FOR ALERT

SOURCE: 8 = I/O

SOURCE DETAIL: 9 = serial SOURCE ID: 0

PROBLEM DETAIL: 3 = functional failure



LEDs: RUN ATTENTION FAULT REMOTE POWER

FLASH OFF OFF OFF ON

LED State: Running non-OS code. (i.e. Boot or Diagnostics)



0x00000063890014C0 00000000 00000000 - type 0 = Data Field Unused

0x58000863890014C0 00006900 1A022A06 - type 11 = Timestamp 01/26/2005 02:42:06

A/a: ack read of this entry - Q/q: quit Virtual Front Panel Display

Anything else redisplay the log entry

->Choice:Timeout!

*****************************************



*****************************************



************ EARLY BOOT VFP *************

End of early boot detected

*****************************************

10 seconds expired.

Proceeding...





로그는 뿌리지만 .. 부팅은 됩니다..

부탁 드릴게요...

수고하세여..

[김병수]

저도 예전에 이런 error를 보았습니다.



장애가 serial port로 나오는 것을 보아 console path에 문제가 있어 보입니다.



console path를 바꾸고 난후에 해결이 되었습니다.



해결은 아래와 같이...



Main Menu: Enter command or menu > path



Primary boot path: intscsia.15

0/0/1/1.15

0/0/01/01.f (hex)



Alternate boot path: intscsib.15

0/0/2/1.15

0/0/02/01.f (hex)



Console path: 0/0/4/1.0

0/0/04/01.0 (hex)



Keyboard path: 0/0/4/0.0

0/0/04/0.0 (hex)



console path 를 0/0/4/0 에서 /0/0/4/1로 change 한다



MAIN> pa co



Thos will tell you what the console path is set to. If it is 0/0/4/0 then do the following



MAIN> pa co 0/0/4/1



This will take care of it. Now do the following..



MAIN> RESET







change 후



Main Menu: Enter command or menu > reset



이error는 아래의 내용을 참조하세요



참조 : PDC firmware 42.09 에서 최초 발생했슴 , version이 낮으면 upgrade해야합니다.



물론 GSP firmware도 upgrade해주면 OK~~~~





그럼 잘되길 바랍니다.

[고광태]

분석해보면

CC_BOOT_NO_GO_SS_CONS

즉 의미는 아래를 읽어보면 됨.

간단하게 말하면 console path 가 정확하지 않기 때문에 뜨는 에러로 볼수가 있음.보통 default로 0/0/4/0 인데 0/0/4/1 로 찾아가기 때문에 그런것임. 새로운 GSP 가 다른 콘솔패스를 가지고 있는것임.



This CC is complaining about incorrect console path in stable storage. This is

a problem on the console path for the new GSP card A6696B (Maestro). It looks

like with the new System Board being installed, the default console path is set

to 0/0/4/0. However if this system has the new GSP Maestro card installed, the

console path is set to 0/0/4/1. This new GSP card uses different console path

(0/0/4/1) and previous GSP card(Tosca) uses the path 0/0/4/0.



L 클래스의 경우는 firmware 를 업그레이드 하면 자동으로 맞춤.



Basically if the system board of the L-class have the new GSP card (A6696B),

one needs to re-configure the console path to 0/0/4/1 if the PDC version

is "40.43" or prior. However, PDC 41.39 is smart enough to tell the difference

between the 2 types of GSP cards Tosca and Maestro. PDC 41.39 should

automatically configure the system console path correctly.



Will write to the Jeff about this.



참조하도록..