HP-UX

K260 Main Board 교체

 
김해종
조언자

K260 Main Board 교체

안녕하세요.. K260 Memory Carrier 불량으로 K260 Main Board 교체하려고 하는 데 절차 좀 알려주세요(SS_Config 변경하는 방법)

수고하세요.
2 응답 2
김병수
본과생

K260 Main Board 교체

ss_config 하는 방법입니다.



1. ss_config 이미지를 받은 다음 (이것은 HPRC에 문의하시면 됩니다.)

dd if=ss299lif.bin of=/dev/rmt/c201d31nb bs=2k(dat로 받습니다.)

(주의할점은 DDS3 tape으로 받으면 DDS2로 부을때 에러가 날 수 있답니다.

이경우 mksf -C tape -H 8.4.1 -b D1600 -n /dev/rmt/sysone 이런식으로 따로

device를 만들어야 합니다)



2. DAT로 부팅



3. ISL> prompt가 떨어집니다.



4. ISL> ss_config(ls를 치시면 tape 내용이 나옵니다.)



5. codeword ---- password (hprc에 문의하시면 됩니다.)



6. password를 넣으면 ss_config 메뉴가 떨어집니다.



7. #MODELSTR(HELP 를 치면 관련 명령어 나옵니다. )



8. 9000/819/K200(K200 strings)



9. SAVE



10. quit --- reboot



그럼~~
고광태
중학생

K260 Main Board 교체

ISL> ss_config





***********************************************************************

******* ******

******* SS_CONFIG ******

******* ******

******* (C) Copyright Hewlett-Packard Co 1991,1992 ******

******* All Rights Reserved ******

******* ******

******* THIS PROGRAM IS NOT LICENSED TO CUSTOMERS ******

******* ******

******* This program is intended for use by trained HP support ******

******* personnel only. HP shall not be liable for any damages ******

******* resulting from unauthorized use of this program. This ******

******* program is the property of HP ******

******* ******

******* Version A.02.21 ******

******* ******

***********************************************************************



Lockword : B67F9C459

Enter Password (Hex): /* Use HP110 or call CRC */







===================================================================

======================== Start of SS_CONFIG =======================

===================================================================



SS->



*******************************************************************

* Die help Funktion listet die verf갾baren Kommandos auf.

*******************************************************************

SS-> help







SS_CONFIG Commands List:



ALTPATH

AUTOBOOT

AUTOSEARCH

BOOTID

CHECKRTC

CHECKSC

CONSPATH

DISPLAY

EXIT

HELP

LANID

LIST

MODELSTR

NOMINALRTC

NOMINALSC

PRIMPATH

RTCLOCK

SAVE

SWCAP

SWID

SYSCLOCK



* Path is BC0/BC1/BC2/BC3/BC4/BC5/PM.L1.L2.L3.L4.L5.L6



*******************************************************************

* Die gespeicherten Einstellungen im Stable Storage k봭nen mit

* display angezeigt werden.

*******************************************************************





SS-> display







Autoboot: ON Autosearch: ON

Primary Boot Path: 52.6.0.0.0.0.0

Alternate Boot Path: 52.0.0.0.0.0.0

Console I/O Path: 56.0.0.0.0.0.0

System Clock: 64 MHz

Real Time Clock: Need NOMINALRTC to compute the frequency



HVERSION: 0x2830

SVERSION: 0x481

Model String (HP UX): 9000/800 /* Incorrect Model String */

SW_ID: 400600202 /* Incorrect SW_ID */

SW_CAP: 0x00 /* Incorrect SW_CAP */



Values have NOT been modified, Stable Storage is current.



*******************************************************************

* Die Software Capability wird mit dem Programm swcap gesetzt.

*******************************************************************





SS-> swcap







Select One Of The Following:

(0) HP-UX

(1) MPE



Your Selection: 0



Enter A Code (0 to 15): 0 /* On all HP-UX Multiuser Systems= 0 */





Values have been modified, Stable Storage needs updating.

Use SAVE command to update values in Stable Storage.



*******************************************************************

* Der Software Identifier wird mit swid auf den richtigen Wert

* eingestellt. Wichtig ist bei Upgrades, da?immer die Original

* Model Number, d.h. die Model Number mit der das System

* urspr걆glich ausgeliefert wurde, eingegeben wird.

*******************************************************************





SS-> swid







Enter The Ten Digit System Serial Number: 3140G00967



Enter The Original System Model Number: A1765A /* Also when System */

/* has been upgraded */



Values have been modified, Stable Storage needs updating.

Use SAVE command to update values in Stable Storage.



*******************************************************************

* Der Model String wird beim Update Programm und Kernel Build

* abgefragt und mu?mit modelstr auf den richtigen Wert ein-

* gestellt werden.

*******************************************************************





SS-> modelstr







Select Which Model String to Set:



(0) HP-UX

(1) OSF

(2) MPE





Your Selection: 0





Enter String: 9000/867 /* Refer to Model String Table */

/* for correct Model String. */



The Model String (HP UX) has been set to 9000/867



Values have been modified, Stable Storage needs updating.

Use SAVE command to update values in Stable Storage.



*******************************************************************

* Sind alle Settings eingestellt, werden die Werte mit save in den

* Stable Storage gespeichert. Mit display kann man abschlie?nd

* nochmals die gespeicherten Settings 갶erpr갽en.

*******************************************************************





SS-> save







Read-back & confirm stable store contents:

Architected variables: OK.

Non-architected variables: OK.

NVM: OK.

EEPROM: OK.

Stable Storage successfully updated



SS-> display







Autoboot: ON Autosearch: ON

Primary Boot Path: 52.6.0.0.0.0.0

Alternate Boot Path: 52.0.0.0.0.0.0

Console I/O Path: 56.0.0.0.0.0.0

System Clock: 64 MHz

Real Time Clock: Need NOMINALRTC to compute the frequency





HVERSION: 0x2830

SVERSION: 0x481

Model String (HP UX): 9000/867 /* Has been modified. */

SW_ID: 797605162 /* Has been modified. */

SW_CAP: 0xF0 /* Has been modified. */





Values have been modified, Stable Storage has been updated.



SS-> exit





Changes were made to Stable Storage.





===================================================================

======================== End of SS_CONFIG =======================

===================================================================