- Community Home
- >
- HPE Community, Korea
- >
- HP-UX
- >
- kernel parm 관련 입니다.
HP-UX
1753663
회원
5688
온라인
108798
솔루션
포럼
범주
Company
Local Language
뒤로
포럼
토론 게시판
포럼
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
토론 게시판
토론 게시판
포럼
토론 게시판
뒤로
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
블로그
정보
커뮤니티 언어
언어
포럼
블로그
- 신규로 표시
- 북마크
- 구독
- 소거
- RSS 피드 구독
- 강조
- 인쇄
- 부적절한 컨텐트 신고
날짜: 01-15-2004 11:00 PM
날짜: 01-15-2004 11:00 PM
kernel parm 관련 입니다.
안녕하세요.
SAM 을 사용하여 커널 파라미터를 바꿀 때
제한된 값 이상으로 바꾸려면 어떻게 하여야 하는지요?
SAM 없이 명령어로 커널 리빌드를 해야 하는지
아니면 특정 화일의 값을 바꾸어야 하는지요?
제 기억에는 특정 화일의 값을 바꾸었던 걸로 기억 하는데
다른 서버에도 적용하려니 기억이 나지 않습니다.
수고하세요.
SAM 을 사용하여 커널 파라미터를 바꿀 때
제한된 값 이상으로 바꾸려면 어떻게 하여야 하는지요?
SAM 없이 명령어로 커널 리빌드를 해야 하는지
아니면 특정 화일의 값을 바꾸어야 하는지요?
제 기억에는 특정 화일의 값을 바꾸었던 걸로 기억 하는데
다른 서버에도 적용하려니 기억이 나지 않습니다.
수고하세요.
3 응답 3
- 신규로 표시
- 북마크
- 구독
- 소거
- RSS 피드 구독
- 강조
- 인쇄
- 부적절한 컨텐트 신고
날짜: 01-15-2004 11:00 PM
날짜: 01-15-2004 11:00 PM
kernel parm 관련 입니다.
안녕하세요~
이종민입니다.
/usr/conf/master.d/core-hpux 에서 수정하시면 됩니다.
이때, * 표 지우지 마시구요
그럼~
이종민입니다.
/usr/conf/master.d/core-hpux 에서 수정하시면 됩니다.
이때, * 표 지우지 마시구요
그럼~
- 신규로 표시
- 북마크
- 구독
- 소거
- RSS 피드 구독
- 강조
- 인쇄
- 부적절한 컨텐트 신고
날짜: 01-15-2004 11:00 PM
날짜: 01-15-2004 11:00 PM
kernel parm 관련 입니다.
제기억으로는
/usr/conf/master.d/core-hpux 를 수정하면
# mv /var/sam/boot.config boot.config.org로 바꾼다음
# /usr/sam/lbin/getkinfo -b 하는 것으로 알고 있습니다.
하지만 sam을 사용할것을 권장하며, max값보다 더 큰값을 입력하면
booting 이 되지 않는 경우도 있으니 매우 조심햐여 주시기 바랍니다.
반드시 bakcup을 받고 작업을 하여 주시기 바랍니다.
그럼~~
/usr/conf/master.d/core-hpux 를 수정하면
# mv /var/sam/boot.config boot.config.org로 바꾼다음
# /usr/sam/lbin/getkinfo -b 하는 것으로 알고 있습니다.
하지만 sam을 사용할것을 권장하며, max값보다 더 큰값을 입력하면
booting 이 되지 않는 경우도 있으니 매우 조심햐여 주시기 바랍니다.
반드시 bakcup을 받고 작업을 하여 주시기 바랍니다.
그럼~~
- 신규로 표시
- 북마크
- 구독
- 소거
- RSS 피드 구독
- 강조
- 인쇄
- 부적절한 컨텐트 신고
날짜: 01-15-2004 11:00 PM
날짜: 01-15-2004 11:00 PM
kernel parm 관련 입니다.
1. /usr/conf/master.d/core-hpux에서 수정을 한다.
2. /var/sam/boot.config를 제거한다.. rm으로..
3. /usr/sam/lbin/getkinfo -b 실행
4. /var/sam 에서 boot.config가 새로 생성되었는지 확인한다.
5. sam에서 커널을 수정한다..
참고: 커널패치 적용시 core-hpux가 디폴터로 변경됩니다..
아래 문서를 참조하세요..
Good day~~
< www.itrc.hp.com 문서 발췌 >
CONFIGURATION
hpux 11.00
RESOLUTION
In order to re-define the maximum limits used by SAM when tuning the shmmni and shmseg kernel parameters, the following is needed. A change can be made to the file /usr/conf/master.d/core-hpux as follows, change the entry:
*range shmmni<=1024
to
*range shmmni<=4096
If needed, make this type of change for shmseg.
Once the changes have been made to core-hpux, remove /var/sam/boot.config and run the following:
/usr/sam/lbin/getkinfo -b
and then confirm that a new boot.config file has been created in /var/sam. Then the changes can be made in SAM.
WARNING: Since /usr/conf/master.d/core-hpux can be replaced by a patch, if this problem of getting past 1024 arises again, the first thing to check is if the core-hpux file has been replaced, and if so repeat the above changes.
2. /var/sam/boot.config를 제거한다.. rm으로..
3. /usr/sam/lbin/getkinfo -b 실행
4. /var/sam 에서 boot.config가 새로 생성되었는지 확인한다.
5. sam에서 커널을 수정한다..
참고: 커널패치 적용시 core-hpux가 디폴터로 변경됩니다..
아래 문서를 참조하세요..
Good day~~
< www.itrc.hp.com 문서 발췌 >
CONFIGURATION
hpux 11.00
RESOLUTION
In order to re-define the maximum limits used by SAM when tuning the shmmni and shmseg kernel parameters, the following is needed. A change can be made to the file /usr/conf/master.d/core-hpux as follows, change the entry:
*range shmmni<=1024
to
*range shmmni<=4096
If needed, make this type of change for shmseg.
Once the changes have been made to core-hpux, remove /var/sam/boot.config and run the following:
/usr/sam/lbin/getkinfo -b
and then confirm that a new boot.config file has been created in /var/sam. Then the changes can be made in SAM.
WARNING: Since /usr/conf/master.d/core-hpux can be replaced by a patch, if this problem of getting past 1024 arises again, the first thing to check is if the core-hpux file has been replaced, and if so repeat the above changes.
위에 명시된 의견은 Hewlett Packard Enterprise가 아닌 저자의 개인 의견입니다. 이 사이트를 사용하면 이용 약관에 동의하게되며 참여 규칙 .
뉴스 및 이벤트
© Copyright 2024 Hewlett Packard Enterprise Development LP