3PAR 7200 SSD Config

[HAAZ]

Hi 

as you can see in bellow the scope status of 3par Serv 7200

3par_SOBM_01 cli% showcage
Id Name LoopA Pos.A LoopB Pos.B Drives Temp RevA RevB Model Side
0 cage0 1:0:1 0 0:0:1 0 16 30-32 320c 320c DCN1 n/a

3par_SOBM_01 cli% showpd
----Size(MB)----- ----Ports----
Id CagePos Type RPM State Total Free A B Cap(GB)

0 0:0:0 FC 10 normal 838656 757760 1:0:1* 0:0:1 900
1 0:1:0 FC 10 normal 838656 758784 1:0:1 0:0:1* 900
2 0:2:0 FC 10 normal 838656 759808 1:0:1* 0:0:1 900
3 0:3:0 FC 10 normal 838656 760832 1:0:1 0:0:1* 900
4 0:4:0 FC 10 normal 838656 761856 1:0:1* 0:0:1 900
5 0:5:0 FC 10 normal 838656 760832 1:0:1 0:0:1* 900
6 0:6:0 FC 10 normal 838656 760832 1:0:1* 0:0:1 900
7 0:7:0 FC 10 normal 838656 758784 1:0:1 0:0:1* 900
8 0:12:0 FC 10 normal 838656 761856 1:0:1* 0:0:1 900
9 0:13:0 FC 10 normal 838656 760832 1:0:1 0:0:1* 900
10 0:14:0 FC 10 normal 838656 760832 1:0:1* 0:0:1 900
11 0:15:0 FC 10 normal 838656 759808 1:0:1 0:0:1* 900
12 0:16:0 FC 10 normal 838656 758784 1:0:1* 0:0:1 900
13 0:17:0 FC 10 normal 838656 759808 1:0:1 0:0:1* 900
14 0:18:0 FC 10 normal 838656 760832 1:0:1* 0:0:1 900
15 0:19:0 FC 10 normal 838656 760832 1:0:1 0:0:1* 900
------------------------------------------------------------------
16 total 13418496 12163072

3par_SOBM_01 cli% showcpg
no cpg listed

3par_SOBM_01 cli% showport
N:S:P Mode State ----Node_WWN---- -Port_WWN/HW_Addr- Type Protocol Label Partner FailoverState
0:0:1 initiator ready 50002ACFF7004B96 50002AC001004B96 disk SAS DP-1 - -
0:0:2 initiator loss_sync 50002ACFF7004B96 50002AC002004B96 free SAS DP-2 - -
0:1:1 target ready 28110002AC004B96 20110002AC004B96 host FC - 1:1:1 none
0:1:2 target ready 28120002AC004B96 20120002AC004B96 host FC - 1:1:2 none
0:3:1 peer offline - B4B52FA73045 rcip IP RCIP0 - -
1:0:1 initiator ready 50002ACFF7004B96 50002AC101004B96 disk SAS DP-1 - -
1:0:2 initiator loss_sync 50002ACFF7004B96 50002AC102004B96 free SAS DP-2 - -
1:1:1 target ready 29110002AC004B96 21110002AC004B96 host FC - 0:1:1 none
1:1:2 target ready 29120002AC004B96 21120002AC004B96 host FC - 0:1:2 none
1:3:1 peer offline - 843497661715 rcip IP RCIP1 - -
-------------------------------------------------------------------------------------------------------

thanks

[Sheldon Smith]

Since there is only one cage, "-ha cage", the default, won't apply to any CPG -- RAID1 would require at least a second cage of disks for "-ha cage" to work.

Try these:

createcpg -sdgs 8g -t r1 -ha mag F1_r1

createcpg -sdgs 8g -t r5 -ha mag F1_r5

Note: While I work for HP, all of my comments (whether noted or not), are my own and are not any official representation of the company.

----------

If my post was useful, click on my KUDOS! "White Star" !