- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- HPE 3PAR StoreServ Storage
- >
- Re: Change Direct attach to fabric attach between ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-07-2020 03:11 PM
тАО02-07-2020 03:11 PM
Change Direct attach to fabric attach between 3par 8200 and c7000 blade enc with two virtual connect
Hello
I Have a 3par 8200 storage with two controller nodes that direct atached to hp c7000 blade enclosure through two virual connect modules.
Two direct attached san fabric is configured on the virual connect ,
the first one use port x1, x2 in the bay one virual connect , the second one use ports x1,x2 in bay two virual connect.
Only port x1 is active in both san fabric , Port x2 is standby in both san fabric.
I have an external SAN Switch(IBM) I want to connect the 3par to the virual connect modules of the blade enclosures through this SAN swich without any down time . what should I Do?
That because :
we want to migrate some VMs from the current 3par to another new 3par (Which also connected to the same external san sw) that migration using Hyper-V.
Connect a veaam backup server to the same external switch for backup the 3par over SAN not over LAN ?
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2020 12:16 AM
тАО02-23-2020 12:16 AM
Re: Change Direct attach to fabric attach between 3par 8200 and c7000 blade enc with two virtual con
Any one have any advice
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-10-2020 10:15 PM
тАО03-10-2020 10:15 PM
Re: Change Direct attach to fabric attach between 3par 8200 and c7000 blade enc with two virtual con
Hi Owahid
Thanks for using Community Forums.
Kindly refer from Page 13 onwards using the below mentioned link.
https://h20628.www2.hp.com/km-ext/kmcsdirect/emr_na-c04448812-6.pdf
See if this helps..
Regards
Mahesh202
I work for HPE.
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]