Query: HPE 3PAR ISCSI

[KushalK123]

I need help to Map Windows host to ISCSI Port. Initiator is showing under host but N:S:P is blank

[support_s]

System recommended content:

1. HPE 3PAR StoreServ iSCSI Best Practices Configuring iSCSI with DCB

2. HPE 3PAR Command Line Interface - iSCSI Port Settings

If the above information is helpful, then please click on "Thumbs Up/Kudo" icon.

Thank you for being a HPE community member.

[KushalK123]

Able to configure ISCSI but host initiator is not showing map to port.

Id Name WWNs Ports Nodes

20 AUX_srvp-qc-bak02 1 0 --

What to do.

[sbhat09]

Hello @KushalK123,

What is the physical NSP of the port? Can you please post the command outputs for showport -i, showport -s and showport -d?

Regards,
Srinivas Bhat

If you feel this was helpful please click the KUDOS! thumb below!
Note: All of my comments are my own and are not any official representation of HPE.

[KushalK123]

 Below are the details.

And concern is 

Host initiator is not showing map to Port.

 showhost VeeamAUX_srvp-qc-bak02.olympu
Id Name Persona -------------------WWN/iSCSI_Name------------------- Port
41 VeeamAUX_srvp-qc-bak02.olympu Generic iqn.2006-06.com.veeam:srvp-qc-bak02.olympus-ossa.com ---

Although other host are mapped.

cli% showhost -pathsum
Id Name WWNs Ports Nodes
40 srv-qc-admin01 1 4 0,1
38 srv-qc-vmx06 1 4 0,1
16 srv-qc-vmx23 1 4 0,1
1 srv-qc-vmx24 1 0 --
18 srv-qc-vmx25 1 4 0,1
5 srv-qc-vmx26 1 4 0,1
6 srv-qc-vmx27 1 4 0,1
7 srv-qc-vmx28 1 4 0,1
27 srv-qc-vmx35 1 4 0,1
25 srvp-qc-bak01 1 0 --
24 srvp-qc-bak02 1 0 --
32 srvp-qc-veeamproxy01 1 4 0,1
10 srvp-qc-vmx01 1 4 0,1
13 srvp-qc-vmx02 1 4 0,1
14 srvp-qc-vmx03 1 4 0,1
30 srvp-qc-vmx04 1 4 0,1
28 srvp-qc-vmx05 1 4 0,1
29 srvp-qc-vmx06 1 4 0,1
37 srvp-qc-vmx07 1 4 0,1
35 srvp-qc-vmx08 1 4 0,1
36 srvp-qc-vmx09 1 4 0,1
31 srvp-qc-vmx10 1 4 0,1
39 srvp-qc-vmx11 1 4 0,1
33 srvp-qc-vmx23 1 4 0,1
34 srvp-qc-vmx24 1 4 0,1
41 VeeamAUX_srvp-qc-bak02.olympu 1 0 --

showport -i
N:S:P Brand Model Rev Firmware Serial HWType
0:0:1 LSI 9205-8e 01 17.11.00.00 Onboard SAS
0:0:2 LSI 9205-8e 01 17.11.00.00 Onboard SAS
0:1:1 EMULEX LPe12002 03 2.10.X.3 Onboard FC
0:1:2 EMULEX LPe12002 03 2.10.X.3 Onboard FC
0:2:1 QLOGIC QLE8242 58 4.15.8 PCGLT0ARC8K01E CNA
0:2:2 QLOGIC QLE8242 58 4.15.8 PCGLT0ARC8K01E CNA
0:3:1 Intel e1000e n/a 3.2.5-k Onboard Eth
1:0:1 LSI 9205-8e 01 17.11.00.00 Onboard SAS
1:0:2 LSI 9205-8e 01 17.11.00.00 Onboard SAS
1:1:1 EMULEX LPe12002 03 2.10.X.3 Onboard FC
1:1:2 EMULEX LPe12002 03 2.10.X.3 Onboard FC
1:2:1 QLOGIC QLE8242 58 4.15.8 PCGLT0AST7YNTV CNA
1:2:2 QLOGIC QLE8242 58 4.15.8 PCGLT0AST7YNTV CNA
1:3:1 Intel e1000e n/a 3.2.5-k Onboard Eth
-----------------------------------------------------------
14
 showport -s
N:S:P --State-- -Detailed_State-
0:0:1 ready ready
0:0:2 ready ready
0:1:1 loss_sync loss_sync
0:1:2 loss_sync loss_sync
0:2:1 ready ready
0:2:2 ready ready
0:3:1 offline offline
1:0:1 ready ready
1:0:2 ready ready
1:1:1 loss_sync loss_sync
1:1:2 loss_sync loss_sync
1:2:1 ready ready
1:2:2 ready ready
1:3:1 offline offline
--------------------------------
14
 showport -d
showport: -d can only be used with -sfp
SYNTAX
showport [options] [-failed] [-sortcol <col>[,<dir>]] [<node:slot:port> |<pattern>...]

[KushalK123]

Can someone assist me on this.

Why initiator is showing under host and port mapping is blank although iscsi configuration is in place.