- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: A-class(a400) is not operating normal.
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-18-2005 12:15 AM
тАО04-18-2005 12:15 AM
A-class(a400) is not operating normal.
When I power on the system,
system just display "Type Ctrl+B to reactivate the GSP command interface"
on standard serial port.
Not display Boot Console Handler(BCH), so I cann't boot from cdrom.
I hit "Return" but nothing happens.
But, GSP service and Secure Web Console are normal operation.
Front Panel LEDs are
RUN is flashing, Attn is off, Fault is off.
I find that this state;
System may be hung or waiting for BCH response
Potential causes could be PDC never executed (problem with fetching code from PDH), HPMC while PDC was configuring system.
I want to install hpux on this server.
Any ideas?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-18-2005 12:18 AM
тАО04-18-2005 12:18 AM
Re: A-class(a400) is not operating normal.
Try resetting through GSP and see if it works.
press Ctrl B
Press enter twice.
type RS
and this would reset the system.
Regards,
Naveej
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-18-2005 12:31 AM
тАО04-18-2005 12:31 AM
Re: A-class(a400) is not operating normal.
If you are using a 700/92 terminal (or 700/96), you can power off the terminal, hold down the "d" key, and power the terminal back on while still holding the "d" key. Count to about 5 and let go of the "d" key. You should get a message on the screen that says "default configs used, press return to clear", hit return and the hardware of the terminal will have been reset.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-18-2005 12:43 AM
тАО04-18-2005 12:43 AM
Re: A-class(a400) is not operating normal.
On HP Consoles there is a "remote mode" Menu in the bottom of the terminal. It should always marked with '*' for your input to reach server. Just check this.
System seems to be normal it is only a terminal settings problem. You said it displays this on standard serial port. Does not it have a console port ? Try connecting to console port instead.
HTH,
Devender
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-18-2005 12:15 PM
тАО04-18-2005 12:15 PM
Re: A-class(a400) is not operating normal.
But I have to explain additional status.
I'm using a notebook for console.
It is ok because it used to connect another A500 system.
and nothing happen when I command RS on GSP.
could you please another explain?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-19-2005 01:54 AM
тАО04-19-2005 01:54 AM
Re: A-class(a400) is not operating normal.
If GSP is not responding properly try to reset GSP with GSP reset button with pin available in the back side of the server.
(this is available in Rp24xx series, should be available in A400, if not remove the power cord and connect it back)
Even after hard reset if GSP is not responding properly, the GSP could be faulty.
Since you tested your laptop with another A400, I guess the GSP itself may be the issue. ( I hope you are using same cable)
Note: I have similar problem in Rp2470 and found that the GSP was faulty.
Regds
Tt