HPE 9000 and HPE e3000 Servers
cancel
Showing results for 
Search instead for 
Did you mean: 

Cable Specifications / Diagram for Composite Port

 
SOLVED
Go to solution
Bharat Katkar
Honored Contributor

Cable Specifications / Diagram for Composite Port

Hi all,
I have rp2450 servers and don't have composite port cable which gives out Console/UPS/Remote ports. Now i want to have console access so i have installed Digiport Box and configured IP address for the same.
But how do i connect this to composite port of the server to DigiBox. My digiport Box end is RJ45 and at server i have a composite port.
Can anybody give me the details of single cable used or cable diagram (25 pin mail to RJ45) in order to get access of console by telnetting the DigiBox.
Thanks in advance and awaiting for your replies.

Bharat
You need to know a lot to actually know how little you know
11 REPLIES 11
Joseph Loo
Honored Contributor

Re: Cable Specifications / Diagram for Composite Port

hi bharat,

you may like to refer to this pdf of cable in the rp2400 series:

http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00044182/c00044182.pdf

regards.
what you do not see does not mean you should not believe
Bharat Katkar
Honored Contributor

Re: Cable Specifications / Diagram for Composite Port

Joseph,
Nice to see your reply but the question is i don't have that w cable A5191-63001 (Refer page no. 7 of your PDF file). And now i want to connect my console terminal directly to the composite port. So what type of cable i need to design or do you have any cable diagram for the same.
Hope got my point. Awaiting for your reponse.
Thanks
Bharat
You need to know a lot to actually know how little you know
Bharat Katkar
Honored Contributor

Re: Cable Specifications / Diagram for Composite Port

??
You need to know a lot to actually know how little you know
Bruno Ganino
Honored Contributor

Re: Cable Specifications / Diagram for Composite Port

Hi Bharat, see this pdf file
http://www.afrts.osd.mil/tech_info/handbook/pdf/section10.pdf

Regards
Bruno
Torino (Turin) +2H
Bruno Ganino
Honored Contributor

Re: Cable Specifications / Diagram for Composite Port

For info connector general
see also this
http://www.geocities.com/luilakes/pinouts.htm

Bruno
Torino (Turin) +2H

Re: Cable Specifications / Diagram for Composite Port

if you have an hp 700/96 terminal and a standard hp terminal cable 24542G you can directly connect the terminal 9 pin port to the rp's 25 pin port, then configure the terminal to use serial 2 and theres your console
Bharat Katkar
Honored Contributor

Re: Cable Specifications / Diagram for Composite Port

Simon,
I don't have 24542G cable. Only the composite port and the terminal.
Thanks,
You need to know a lot to actually know how little you know
Highlighted
Ted Buis
Honored Contributor

Re: Cable Specifications / Diagram for Composite Port

I couldn't find the pinouts but the W cable has part number A5191-63001 ($36) from HP.
Mom 6
Naveej.K.A
Honored Contributor

Re: Cable Specifications / Diagram for Composite Port

Hi Bharat,

some h/w basics, rs232 communication uses pin numbers 2,3&7 for rx,tx and ground for establishing the communication.

I don't know how a digi port box looks like, but if you got a 25 pin mail connector and you could plug it behind the GSP card, the pin numbers 2,3&7 are the one which communicates with the console....

how is your console?? with male or female connection. I have a female connection on the console side....

so the ends of my cable would look something like

pin layout of cable on server side(male) ==>> pin lay out of male cable at console
2 ==> 3
3 ==> 2
7 ==> 7

with best wishes
Naveej
practice makes a man perfect!!!