- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: Cannot boot an A500 server
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-08-2003 11:04 PM
тАО04-08-2003 11:04 PM
Last days I saw some 'SCSI reset' messages in syslog.log when 'ioscan -f' command is executed.
Now I rebooted the system bu it cannot boot.
It loads kernel and display
Boot
: disk(0/0/1/1.15.0.0.0.0.0;0)/stand/vmunix
7909376 + 1220456 + 1137200 start 0x254ae8
alloc_pdc_pages: Relocating PDC from 0xf0f0000000 to 0x5faab000.
After 5 minutes or more, a GSP system alert is shown and prompted for keyboard typing:
************* SYSTEM ALERT **************
SYSTEM NAME: MBBDDGSP
DATE: 04/09/2003 TIME: 06:32:48
ALERT LEVEL: 12 = Software failure
REASON FOR ALERT
SOURCE: 1 = processor
SOURCE DETAIL: 1 = processor general SOURCE ID: 0
PROBLEM DETAIL: 0 = no problem detail
LEDs: RUN ATTENTION FAULT REMOTE POWER
FLASH FLASH OFF ON ON
LED State: Running non-OS code. Non-critical error detected.
Check Chassis and Console Logs for error messages.
0xF8E000C01100B800 00000000 0000B800 - type 31 = legacy PA HEX chassis-code
0x58E008C01100B800 00006703 09062030 - type 11 = Timestamp 04/09/2003 06:32:48
A: ack read of this entry - X: Disable all future alert messages
Anything else skip redisplay the log entry
Can anyone help me ?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-09-2003 12:00 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-09-2003 12:51 AM
тАО04-09-2003 12:51 AM
Re: Cannot boot an A500 server
After disabling "Alert Logs" in GSP, the error message is displayed:
Console reset done.
Boot device reset done.
Stored message buffer up to panic:
: 0
SCSI: Reset detected -- lbolt: 645, bus: 0
SCSI: Reset detected -- lbolt: 662, bus: 0
SCSI: Res...
System Panic:
linkstamp: Tue Dec 17 07:28:01 MET 2002
_release_version: @(#)B2352B/9245XB HP-UX (B.11.00) #1: Wed Nov 5 22:38:19 PS
T 1997
__kern_ci_revision: $Header: kern_sequence.c,v 1.6.106.512 97/11/05 18:01:46 mso
sa Exp $
panic: I/O system hang
PC-Offset Stack Trace (read across, top of stack is 1st):
0x00339ccc 0x00415408 0x000ddba8
0x0003e1a0 0x0034d018 0x00135124
0x0012cb00 0x0013019c
End Of Stack
*** A system crash has occurred. (See the above messages for details.)
*** The system is now preparing to dump physical memory to disk, for use
*** in debugging the crash.
ERROR: Your system crashed before I/O and dump configuration was complete.
A crash dump cannot be taken under these circumstances without
special configuration. Contact your HP support representative
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-20-2006 05:59 PM
тАО04-20-2006 05:59 PM
Re: Cannot boot an A500 server
I am facing a similar problem on my A-class server. The boot hangs at alloc_pdc_pages: Relocating PDC from 0xxxxxx.
Can you let me know if you could solve itand how?
TIA
Rashmi.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-12-2006 10:55 PM
тАО11-12-2006 10:55 PM