- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- E25 Console problem
HPE 9000 and HPE e3000 Servers
1753556
Members
5511
Online
108796
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2009 01:28 PM
тАО02-22-2009 01:28 PM
Hello Everyone,
I have two E25 systems and I cannot seem to get the console to respond on either of them. I did have to upgrade the systems so that they had the 16 port mux in them. I have tried several console cables and cables between the System and the DDP-2 Cable and still absolutely no response. The attention light stays on but other than that I get no response.
I still should be able to do aB to gain access to the boot menu, shouldn't I. I am attached to port 0 on the DDP-2 panel to the serial port on a 700/96 ascii terminal.
I know this is a VERY old system so any help would be greatly appreciated.
Tim
I have two E25 systems and I cannot seem to get the console to respond on either of them. I did have to upgrade the systems so that they had the 16 port mux in them. I have tried several console cables and cables between the System and the DDP-2 Cable and still absolutely no response. The attention light stays on but other than that I get no response.
I still should be able to do a
I know this is a VERY old system so any help would be greatly appreciated.
Tim
Solved! Go to Solution.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-24-2009 05:43 AM
тАО02-24-2009 05:43 AM
Solution
cool that still these systems are used :-)
I guess you have the MUX panel:
DDP, 16 Channel 0950-2431
and the cable:
Cable, 16-port to ADP & DDP A1703-69305
?
What do9 you mean with "16 port MUX in them" ?
You only can use control B if the access port switch is enabled on the CPU card.
But if this has worked with your old MUX hardware, then this is still a MUX problem or you have the wrong cable.
best regards
Stefan
I guess you have the MUX panel:
DDP, 16 Channel 0950-2431
and the cable:
Cable, 16-port to ADP & DDP A1703-69305
?
What do9 you mean with "16 port MUX in them" ?
You only can use control B if the access port switch is enabled on the CPU card.
But if this has worked with your old MUX hardware, then this is still a MUX problem or you have the wrong cable.
best regards
Stefan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-24-2009 09:21 AM
тАО02-24-2009 09:21 AM
Re: E25 Console problem
Thanks for your response Stefan!
Here is the configuration of the system.
CPU card P/N A2051-66501
SCSI/PRINTER/APMUX16 card P/N A1703-60022
ADP/DDP cable P/N 5062-3100 (this goes from the card to the two DDP-2 pannels)
2ea DDP-2 Pannels P/N 5181-2085
Console Cable P/N 40242-60020
Console P/N 700/96
The light on the ADP/DDP port does not come on when everything is connnected. I am not sure if it is suppose to or not.
Tim
Here is the configuration of the system.
CPU card P/N A2051-66501
SCSI/PRINTER/APMUX16 card P/N A1703-60022
ADP/DDP cable P/N 5062-3100 (this goes from the card to the two DDP-2 pannels)
2ea DDP-2 Pannels P/N 5181-2085
Console Cable P/N 40242-60020
Console P/N 700/96
The light on the ADP/DDP port does not come on when everything is connnected. I am not sure if it is suppose to or not.
Tim
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP