- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- GSP Flow Control
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-20-2007 12:01 AM
тАО07-20-2007 12:01 AM
GSP Flow Control
Guardian Service Processor WARNING: GSP is permanently flow controlled very likely by
the local serial port. You need to remove the flow control condition.
How I can resolve this problem?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-20-2007 12:11 AM
тАО07-20-2007 12:11 AM
Re: GSP Flow Control
Check the serial port settings with
GSP> ca
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-20-2007 12:25 AM
тАО07-20-2007 12:25 AM
Re: GSP Flow Control
CA
This command allows you to modify the local and remote modem serial port
configurations. Current configuration settings:
Local Console Serial Port bit rate: 9600 bits/s
Local Console Serial Port Flow Control:
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-20-2007 12:44 AM
тАО07-20-2007 12:44 AM
Re: GSP Flow Control
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-20-2007 12:46 AM
тАО07-20-2007 12:46 AM
Re: GSP Flow Control
This command allows you to modify the local and remote modem serial port
configurations. Current configuration settings:
Local Console Serial Port bit rate: 9600 bits/s
Local Console Serial Port Flow Control:
Guardian Service Processor WARNING: GSP is permanently flow controlled very likely by
the local serial port. You need to remove the flow control condition.
Hardware
Local Console Serial Port Terminal Type: vt100
Remote Console Serial Port Modem Protocol: CCITT
Remote Console Serial Port Modem bit rate: 19200 bits/s
Remote Console Serial Port Modem Flow Control: Software
Remote Console Serial Port Modem Transmit Configuration Strings: Enabled
Remote Console Serial Port Modem Presence:
Guardian Service Processor WARNING: GSP is permanently flow controlled very likely by
the local serial port. You need to remove the flow control condition.
always connected
Do you want to modify the Local Console Serial Port settings? (Y/[N])
Do you want to modify the Remote Console Serial Port Modem settings? (Y/[N]) y
y
Current Remote Console Serial Port Modem Protocol: CCITT
Do you want to modify it? (Y/[N]) y
y
Enter Modem Protocol (Bell / CCITT):
Sorry, wrong input...
Current Remote Console Serial Port
Guardian Service Processor WARNING: GSP is permanently flow controlled very likely by
the local serial port. You need to remove the flow control condition.
Modem Protocol: CCITT
Do you want to modify it? (Y/[N])
Current Modem bit rate: 19200 bits/s
Do you want to modify it? (Y/[N])
Current Flow Control: Software
I must set HARDWARE?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-20-2007 12:53 AM
тАО07-20-2007 12:53 AM
Re: GSP Flow Control
http://www.docs.hp.com/en/A5191-96018/ch04s03.html
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!