HPE 9000 and HPE e3000 Servers
cancel
Showing results for 
Search instead for 
Did you mean: 

GSP Power-On command doesn't work

 
SOLVED
Go to solution
Mauro Gatti
Valued Contributor

GSP Power-On command doesn't work

Hi all,
after a forced shutodown cause by evironment overtemp I'm not able to switch on my server using GSP's PC menu.
Is it normal behaviour?
This is what I get from VFP and PC:

Thank You

RGDS

Mauro

*********************************************

GSP> vfp


VFP

This command activates the immediate display of the Virtual Front Panel.

LEDs: RUN ATTENTION FAULT REMOTE POWER
OFF OFF OFF OFF FLASH
System Power is Off.

platform monitor 6406

***********************************************

GSP> pc


PC

System Power: Off Power Switch: On
Do you wish to turn power On ? (Y/[N]) Y
Y
Enter delay (in minutes) of delay to power On (CR for no delay)?

System will be powered On in 0 minutes.
Confirm? (Y/[N]): Y
Y

The system did not respond to the Power-On command.
Turn the system power switch Off and On again to reset the system.
Ubi maior, minor cessat!
5 REPLIES 5
Shameer.V.A
Respected Contributor

Re: GSP Power-On command doesn't work

Hi Mauro Gatti,
Please give the exact model of your server.

Normally for RP series servers,
You have to go to CM menu from GSP & give PE ( power Entity option ) & it will ask you whether you need to do operations on Cabinet or Cell. Respond accordingly.


Hope this will help you..

Thanks & Regards,

Shameer
.... See invisible, feel intangible and achieve impossible as everything is possible ....
Mauro Gatti
Valued Contributor

Re: GSP Power-On command doesn't work

My server is an A-class.
My GSP version is:
Hardware Revision 8 Firmware Revision A.01.10
and there is any PE menu but only:

==== GSP Help ============================================(Administrator)===
AC : Alert display Configuration PC : Remote Power Control
AR : Automatic System Restart config. PG : PaGing parameter setup
CA : Configure asynch/serial ports PS : Power management module Status
CL : Console Log- view console history RS : Reset System through RST signal
CO : COnsole- return to console mode SDM : Set Display Mode (hex or text)
CSP : Connect to remote Service Proc. SE : SEssion- log into the system
DC : Default Configuration SL : Show Logs (chassis code buffer)
DI : DIsconnect remote or LAN console SO : Security options & access control
EL : Enable/disable LAN access SS : System Status of proc. modules
ER : Enable/disable Remote/modem TC : Reset via Transfer of Control
HE : Display HElp for menu or command TE : TEll- send a msg. to other users
IT : Inactivity Timeout settings VFP : Virtual Front Panel display
LC : LAN configuration WHO : Display connected GSP users
LS : LAN Status XD : Diagnostics and/or Reset of GSP
MR : Modem Reset XU : Upgrade the GSP Firmware
MS : Modem Status

Is it possible I have to upgrade GSP firmware?
Ubi maior, minor cessat!
Sivakumar TS
Honored Contributor
Solution

Re: GSP Power-On command doesn't work


Hi,

Before doing PC on/off,

run PS to check the power enable/disabled status for the Parts.

you may enable the Power by

MP>PE

select...

ON/OFF

Regards,

Siva.
Nothing is Impossible !
Sameer_Nirmal
Honored Contributor

Re: GSP Power-On command doesn't work

Hi,

It seems that the platform monitor has disabled the "power on" on account of overtemperature condition. You need to wait for a while to cool the server down and ensure proper surrounding enviorment for tempreture etc. Refer following link.
http://docs.hp.com/en/2411/rp24xx_customer.pdf

Option "PE" is not an option in the firmware for your server.
Check the GSP -> SL as well.

As far as the GSP firmware upgrade is concerned, the latest GSP A firmware version is A.01.12. It is always recommended to have latest firmware installed in the server.
Mauro Gatti
Valued Contributor

Re: GSP Power-On command doesn't work

Thank You
Ubi maior, minor cessat!