GSP error log message..?????

[???_185]

Hi everyone !!

This is what i got when i check errors with GSP SL command:

************* SYSTEM ALERT **************
SYSTEM NAME: uninitialized
DATE: 07/25/2005 TIME: 06:38:46
ALERT LEVEL: 15 = Fatal hardware or configuration problem prevents operation

REASON FOR ALERT
SOURCE: 4 = power
SOURCE DETAIL: F = unexpected SOURCE ID: F8
PROBLEM DETAIL: 2 = unexpected

LEDs: RUN ATTENTION FAULT REMOTE POWER
ON FLASH OFF OFF ON
LED State: There was a system interruption that did not take the system d
Check Chassis and Console Logs for error messages.

0x000000F24FF8E038 00000002 4F000000 - type 0 = Data Field Unused
0x580008F24FF8E038 00006906 1906262E - type 11 = Timestamp 07/25/2005 06:38:46
A: ack read of this entry - X: Disable all future alert messages
Anything else skip redisplay the log entry


SYSTEM NAME: uninitialized
DATE: 07/25/2005 TIME: 06:40:09
ALERT LEVEL: 6 = Boot possible, pending failure - action required

REASON FOR ALERT
SOURCE: 0 = unknown, no source stated
SOURCE DETAIL: C = unexpected SOURCE ID: D
PROBLEM DETAIL: 9 = unexpected

LEDs: RUN ATTENTION FAULT REMOTE POWER
ON FLASH OFF OFF ON
LED State: There was a system interruption that did not take the system down.
Check Chassis and Console Logs for error messages.

0x120000690C0D0B0B 00000002 06440200 - type 2 = Expected Data
0x5A0008690C0D0B0B 00006906 19062809 - type 11 = Timestamp 07/25/2005 06:40:09
A: ack read of this entry - X: Disable all future alert messages
Anything else skip redisplay the log entry
->Choice:


************* SYSTEM ALERT **************
SYSTEM NAME: uninitialized
DATE: 07/25/2005 TIME: 06:38:46
ALERT LEVEL: 15 = Fatal hardware or configuration problem prevents operation

REASON FOR ALERT
SOURCE: 4 = power
SOURCE DETAIL: F = unexpected SOURCE ID: F8
PROBLEM DETAIL: 2 = unexpected

LEDs: RUN ATTENTION FAULT REMOTE POWER
ON FLASH OFF OFF ON
LED State: There was a system interruption that did not take the system d
Check Chassis and Console Logs for error messages.

0x000000F24FF8E038 00000002 4F000000 - type 0 = Data Field Unused
0x580008F24FF8E038 00006906 1906262E - type 11 = Timestamp 07/25/2005 06:38:46
A: ack read of this entry - X: Disable all future alert messages
Anything else skip redisplay the log entry

Log Entry #
ALERT LEVEL: 6 = Boot possible, pending failure - action required
DATE: 07/25/2005 TIME: 06:50:20

SOURCE: 0 = unknown, no source stated or configuration problem prevents op
SOURCE DETAIL: D = unexpected SOURCE ID: D

SOUR
0x270000690D0D0B13 00000002 06440200 type 4 = Physical Location

0x000000F04FF8E078 00000002 4F000000 ty
0x5F0008690D0D0B13 00006906 19062C13 type 11 = Timestamp 07/25/2005 06:44:19
0x580008F04FF8E078 00006906 19063214 type 11 = Timestamp 07/25/
Type CR for next entry, - CR for previous entry, Q CR to quit.
Type CR for next entry, - CR for pr



Log Entry # 34 :Log Entry # 7 :
SYSTEM NAME: uninitializedME: uninitialized
SOURCE: 6 = platformwer
SOURCE DETAIL: 9 = backplane SOURCE ID: 6F8
PROBLEM DETAIL: 0 = unexpectedcted

CALLER ACTIVITY: 0 = unspecified STATUS: 0: 8
CALLER SUBACTIVITY: 00 = implementation dependentnt
REPORTING ENTITY TYPE: 0 = system firmware REPORTING ENTITY ID: 0500

0x000050E069060000 00000002 08000D00 type 0 = Data Field Unuseded
0x580058E069060000 00006906 19062B31 type 11 = Timestamp 07/25/2005 06:43:4927
Type CR for next entry, - CR for previous entry, Q CR to quit.

[Torsten.]

your power supply #2 has failed. The system is still working, but not redundant. Exchange the power supply!

[Steven E. Protter]

Good news is your system probably has a hot swap power supply that can be replaced while running. If not, at least redundancy will allow you to schedule your downtime.

You have some extra data in gsp and might wish to roll through the logs and erase it after you replace the bad part.

SEP

[generic_1]

Get this replaced asap.
18006333600 is the service number for HP.
Also Check with your facilities, and make sure your leg of power is OK to that side, and that they have not been having problems.

[Sean Dale]

Exactly what the others have said: call the 800 number and have the power supply replaced ASAP.