GSP

[rudy_4]

# stty
speed 9600 baud; evenp hupcl -cread
intr = ^C; erase = ^H; kill = ^U;
swtch ;
brkint -inpck icrnl -ixany ixoff onlcr
-iexten echo echoe echok
-echoctl -echoke



#stty -a

speed 9600 baud; line = 0;
rows = 24; columns = 80
min = 4; time = 0;
intr = ^C; quit = ^\; erase = ^H; kill = ^U
eof = ^D; eol = ^@; eol2 ; swtch
stop = ^S; start = ^Q; susp ; dsusp
werase ; lnext
parenb -parodd cs7 -cstopb hupcl -cread -clocal -loblk -crts
-ignbrk brkint ignpar -parmrk -inpck istrip -inlcr -igncr icrnl -iuclc
ixon -ixany ixoff -imaxbel -rtsxoff -ctsxon -ienqak
isig icanon -iexten -xcase echo echoe echok -echonl -noflsh
-echoctl -echoprt -echoke -flusho -pendin
opost -olcuc onlcr -ocrnl -onocr -onlret -ofill -ofdel -tostop



#ls *GSP*
GSPdiag2
# ls -l /dev/GSPdiag2
crw------- 1 root sys 1 0x000080 May 29 2003 /dev/GSPdiag2


thank again and again

[Olivier Decorse]

Sorry, i mean : what is the exact output of the "stty +resetGSP
It seems that the GSP device have the good rigths ...

Are you really root ? check with "id".

As Naveej says, you can reset the GSP, opening the server.

Olivier.

[rudy_4]

# stty +resetGSP This operation is not permitted.
# id
uid=0(root) gid=3(sys) groups=0(root),1(other),2(bin),4(adm),5(daemon),6(mail),7(lp),20(users)
#

ok but do u think that resetting the gsp will work

[Joseph Loo]

i did more research:

http://www1.itrc.hp.com/service/cki/docDisplay.do?docLocale=en_US&docId=200000072570316

the above seems to be what u r experiencing. u may have to do a firmware upgrade on the GSP if after "hardware" reset, GSP still does not work.


regards.

[Olivier Decorse]

Someone had the same problem as you http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=45715

Solution :
use the reset button on the GSP card ...

Olivier.

[Joseph Loo]

so, is your problem solve by hardware GSP resetting?

regards.

[Jon Steele · Accepted solution]

Rudy,
The reset button on the gsp card is on the side of the card in the machine.You will need to take the side panel off.Then you will see a red gsp reset button.If this does not work I would think your gsp card went bad,as we have had the same problem before.When we changed out the gsp card it worked fine.

Jon

[rudy_4]

soory to keep you still guys does the system have to be shutdown or no need

[Joseph Loo]

there is no need to shutdown. as long as u r able to find that GSP reset button. reset it and it should work.

regards.

[rudy_4]

ok i done that and it gave the press ctrl b but i couldnt press the ctrl b
but i was reading something on the internet and i noticed that they said that the console cable is not right that some one is using a null modem cable for the console and i think i m also using a null modem could this be a problem