- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Installing Modem MT5634ZBA on rp7420
HPE 9000 and HPE e3000 Servers
1753973
Members
7804
Online
108811
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-30-2006 07:41 AM
06-30-2006 07:41 AM
Installing Modem MT5634ZBA on rp7420
Hi
I am installing ZMultiModem MT5634ZBA on HPrp7420 and it connect succesfuly,
MP Login: but when I do login Admin and RETURN it show me only The character ^M ^M^M^M^M^M^M^M^M^M^M^M
1.- I connect the DB9 to DB25 cable in the modem Kit
2.- MP> Modem Protocol is: CCITT
3.- Remote Console Port baud rate: 19200
4.- Flow Control: Software
Can you help me please...
Thanks,
Lorayne
I am installing ZMultiModem MT5634ZBA on HPrp7420 and it connect succesfuly,
MP Login: but when I do login Admin and RETURN it show me only The character ^M ^M^M^M^M^M^M^M^M^M^M^M
1.- I connect the DB9 to DB25 cable in the modem Kit
2.- MP> Modem Protocol is: CCITT
3.- Remote Console Port baud rate: 19200
4.- Flow Control: Software
Can you help me please...
Thanks,
Lorayne
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-30-2006 10:57 AM
06-30-2006 10:57 AM
Re: Installing Modem MT5634ZBA on rp7420
verify these devices: cua0p7, cul0p7 and ttyd0p7 for HP-UX on the server.
Check the MP CA configuration settings within the MP:
CA: Configure local and remote serial port parameters
Set up the local serial port parameters as follows:
â ¢ BAUD RATES: Input and output data rates are the same â 4800, 9600, 19200, 38400, 115200 bit/sec.
â ¢ FLOW CONTROL: Hardware uses RTS/CTS; software uses Xon/Xoff.
Set up the remote serial port parameters as follows:
â ¢ MODEM PROTOCOL: Bell or CCITT. (CCITT is a European standard; RTS/CTS signaling is used, as
well as the Ring signal. Bell is a U.S. or simple mode.)
â ¢ BAUD RATES: Input and output data rates are the same â 4800, 9600, 19200, 38400 bit/sec.
â ¢ FLOW CONTROL: Hardware uses RTS/CTS; software uses Xon/Xoff.
â ¢ TRANSMIT CONFIGURATION STRINGS: Disable this setting whenever the modem being used is not
compatible with the supported modem (MT5634ZBA).
â ¢ MODEM PRESENCE: When the modem might not always be connected, set this parameter to â not
always connected.â
Example: A modem attached through a switch. In mode â not always connected,â no dial-out functions are
allowed: DIAL-BACK is disabled, and PAGING is not possible.
The MP mirrors the system console to the MP local, remote/modem, and LAN ports. One console output
stream is reflected to all of the connected console users. If several different terminal types are used
simultaneously by the users, some users might see unexpected results.
http://www.docs.hp.com/en/5971-4274_iLO_ops/5971-4274_iLO_ops.pdf
Check the MP CA configuration settings within the MP:
CA: Configure local and remote serial port parameters
Set up the local serial port parameters as follows:
â ¢ BAUD RATES: Input and output data rates are the same â 4800, 9600, 19200, 38400, 115200 bit/sec.
â ¢ FLOW CONTROL: Hardware uses RTS/CTS; software uses Xon/Xoff.
Set up the remote serial port parameters as follows:
â ¢ MODEM PROTOCOL: Bell or CCITT. (CCITT is a European standard; RTS/CTS signaling is used, as
well as the Ring signal. Bell is a U.S. or simple mode.)
â ¢ BAUD RATES: Input and output data rates are the same â 4800, 9600, 19200, 38400 bit/sec.
â ¢ FLOW CONTROL: Hardware uses RTS/CTS; software uses Xon/Xoff.
â ¢ TRANSMIT CONFIGURATION STRINGS: Disable this setting whenever the modem being used is not
compatible with the supported modem (MT5634ZBA).
â ¢ MODEM PRESENCE: When the modem might not always be connected, set this parameter to â not
always connected.â
Example: A modem attached through a switch. In mode â not always connected,â no dial-out functions are
allowed: DIAL-BACK is disabled, and PAGING is not possible.
The MP mirrors the system console to the MP local, remote/modem, and LAN ports. One console output
stream is reflected to all of the connected console users. If several different terminal types are used
simultaneously by the users, some users might see unexpected results.
http://www.docs.hp.com/en/5971-4274_iLO_ops/5971-4274_iLO_ops.pdf
Support Fatherhood - Stop Family Law
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP