- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: K-Class Serviceguard Hardware questions
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-29-2007 11:15 PM - last edited on тАО03-16-2014 07:47 PM by Maiko-I
тАО04-29-2007 11:15 PM - last edited on тАО03-16-2014 07:47 PM by Maiko-I
Hi Guys,
Im looking to setup a couple of old K360 servers as a 2 node serviceguard cluster for a training environment. I have most of the hardware availble but its been a long time since i built a cluster on hardware this old.
Both servers have suffcient NIC's and SCSI interfaces and i also have a couple of disk arrays (Surestore E's with A5616A interface cards) I have a box full of SCSI cables but from what i remeber i need some black terminating cables to connect up the disks (so both nodes can see them), Does anybody know the part numbers of these cables as i need to order some asap.
P.S. This thread has been moevd from Disk to Servers > HP 9000. - hp forum moderator
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-29-2007 11:23 PM
тАО04-29-2007 11:23 PM
Solutionthe "inline termination cables" were intended to make the cluster service-able.
By using this cables, you can disconnect the cable (connected to the shared storage) from one server without opening the bus (it is still terminated).
For your training setup you won't need them - but you need to terminate the controllers.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-29-2007 11:41 PM
тАО04-29-2007 11:41 PM
Re: K-Class Serviceguard Hardware questions
The terminators are needed on for the unused connectors on the Surestore unit.
If you need more scci cables, the part number is usually stamped on the card.
For the terminators, see http://partsurfer.hp.com for part numbers.
SEP
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-29-2007 11:43 PM
тАО04-29-2007 11:43 PM
Re: K-Class Serviceguard Hardware questions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-29-2007 11:50 PM
тАО04-29-2007 11:50 PM
Re: K-Class Serviceguard Hardware questions
If you NOT use the cables, you MUST use the internal terminators.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-30-2007 08:06 PM
тАО04-30-2007 08:06 PM
Re: K-Class Serviceguard Hardware questions
The part you require if you want the ILT is a C2980A 0.5m 68pin male 68pin female. I do not know if you can still buy them from HP. However 2nd user suppliers should be able to help.
Mike.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-02-2007 03:37 AM
тАО05-02-2007 03:37 AM