- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: L2000 new hard drive
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-01-2010 10:49 AM
тАО04-01-2010 10:49 AM
L2000 new hard drive
Am I going to have a problem when I install the new harddrives by putting them into the A0 & B0 slots? Is there anything I need to be concerned with when I install the hard drives?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-01-2010 10:52 AM
тАО04-01-2010 10:52 AM
Re: L2000 new hard drive
The system will detect the drives and, either via a reboot or the insf command, assign appropriate c?t?d0 device files.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-01-2010 10:56 AM
тАО04-01-2010 10:56 AM
Re: L2000 new hard drive
B) Did the manufacturer say they were compaitible with a L2000?
c) You're going to have to ignite from scratch to get all 73 gb out of these drives. Else, you will be locked into using only 9 gb since this is what vg00 is currently configured for.
d) Follow a Ignite cloning procedure,
http://forums13.itrc.hp.com/service/forums/questionanswer.do?threadId=1418780
See my resposnes, read carefully as the subject is different, (* igniter versions mismatch *) but the answers are in general the same.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-02-2010 04:34 AM
тАО04-02-2010 04:34 AM
Re: L2000 new hard drive
And L2000 supported 73GB disk, some disks info. as below:
73GB HotPlug Disk 10K A6091-69001 ST173404LC
73GB HotPlug U160 Disk 10K A6738-69002 ATLAS10K3_73_SCA, MAN3735MC U160
73GB HotPlug Ultra320 15k A9761-69001 ST373453LC
73GB Hot Plug Disk 10k A6276-69002 HP 73.2GMAN3373MC, HP 73.2GMAP3735NC
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-02-2010 04:46 AM
тАО04-02-2010 04:46 AM
Re: L2000 new hard drive
Note that this will be a problem unless you account for it during the swap out.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-02-2010 06:37 AM
тАО04-02-2010 06:37 AM
Re: L2000 new hard drive
True, if you want them to be part of VG00.
If you create a new VG with the 73 GB disks there wouldn't be a problem.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2010 07:44 AM
тАО04-03-2010 07:44 AM
Re: L2000 new hard drive
I was planning on creating a vg02 and putting the two drives in to it.
The problem I am having now is that I did a cold install of HP-UX 11.23 on the two 9GB drives (vg00) and now I am not able to connect to the server via Reflections. Actually I can not even ping the server so I might have not had a good OS installation. I am using the webconsole to connect to the server right now. I am going to try to reinstall the OS again today. If I can not resolve this issue then I will have to open another call.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2010 05:46 PM
тАО04-03-2010 05:46 PM
Re: L2000 new hard drive
The installation is probably just fine -- I wouldn't waste time starting over. Your only problem (so far) is your network setup. Always ping by IP address first and from a system that is on the same subnet. If that works, then ping'ing by hostname is a local problem on your PC. You must supply an IP address, subnet mask and gateway address. To do this with your current system, run these commands:
set_parms ip_address
set_parms addl_netwrk
Bill Hassell, sysadmin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2010 06:06 PM
тАО04-03-2010 06:06 PM
Re: L2000 new hard drive
Run
'set_parms initial'
Have all your DNS ip addresses, NTP, default Gateway, hostname, ip of server, etc. collected ahead of time.
To test connectivity to the network
a) ping hostname
b) ping ip address of your server
If these work then the NIC is up with the correct driver
c) ping default gateway
If this fails then check your cables, ie, to the switch.
d) verify same speed and duplex to switch from your nic.
landadmin -x #