- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: LCD fault codes for D-class
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-16-2003 12:39 AM
тАО12-16-2003 12:39 AM
LCD fault codes for D-class
FLT 5002
FLT CBF0
FLT CBF1
FLT CBFC
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-16-2003 01:42 AM
тАО12-16-2003 01:42 AM
Re: LCD fault codes for D-class
5002 - Bus transaction errors.
CBF0 - HPMC occured
CBF1 & CBFC - OS didn't load.
Look like you have corrupted OS.
Try to boot from alternate disk if boot/root
mirrored.
else try to boot from support CD and run diag.
TT
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-16-2003 02:41 PM
тАО12-16-2003 02:41 PM
Re: LCD fault codes for D-class
Based on the document on this url below :
http://www.docs.hp.com/hpux/pdf/A3262-90013.pdf
See chapter 6-9 about 'LCD-Indicated Problems' on pages 96
The FLT means a hardware error has been detected. So better you log call to HP and they will analyse this for you.
Hope this information can help you.
Best Regards,
AW
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-16-2003 02:52 PM
тАО12-16-2003 02:52 PM
Re: LCD fault codes for D-class
May I know the model of your D-class machine ? You can run the 'model' command to check it.
If you have 'D-Class' service manual, you can identified the cause of this message.
Hope this information can help you.
Best Regards,
AW
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-17-2003 02:05 AM
тАО12-17-2003 02:05 AM
Re: LCD fault codes for D-class
At bootup, do the following:
grep HPMC /var/tombstones/ts99
See if you have any codes that look significantly different from thsoe above (like 2xxx or 7xxx).
If you get a 2xxx then the CPU that logged it needs to be replaced.
Anything other then that will probably require a call to HPQ HW support.
Best regards,
Kent M. Ostby